MAX1700EEE Maxim Integrated Products, MAX1700EEE Datasheet - Page 10

• Manufacturer Part Number: MAX1700EEE
• Description: IC CONV DCDC 1-3CELL HP 16-QSOP
• Manufacturer: Maxim Integrated Products
• Type: Step-Up (Boost)r

Specifications of MAX1700EEE

• Internal Switch(s): Yes
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 2.2 ~ 5.5 V
• Current - Output: 800mA
• Frequency - Switching: 300kHz
• Voltage - Input: 0.7 ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-QSOP
• Power - Output: 667mW
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

1-Cell to 3-Cell, High-Power (1A),
Low-Noise, Step-Up DC-DC Converters
Figure 2. Fixed or Adjustable Output (PWM mode).
Table 1. Typical Available Output Current
Table 2. Selecting the Operating Mode
The step-up switching DC-DC converter generates an
adjustable output from 2.5V to 5.5V. During the first part
of each cycle, the internal N-channel MOSFET switch is
turned on. This allows current to ramp up in the induc-
tor and store energy in a magnetic field. During the
second part of each cycle, when the MOSFET is turned
off, the voltage across the inductor reverses and forces
current through the diode and synchronous rectifier to
10
1 NiCd/NiMH
2 NiCd/NiMH
2 NiCd/NiMH
3 NiCd/NiMH
(200kHz to 400kHz)
0.22 F
OF CELLS
or 1 Li-Ion
NUMBER
22 F
External Clock
0.7V TO 5.5V
______________________________________________________________________________________
CLK/SEL
OUT
0
1
CLK/SEL
ONA
ONB
REF
VOLTAGE (V)
GND
MAX1700
MAX1701
INPUT
1.2
2.4
2.4
3.6
Synchronized
PGND
Low Power
POUT
OUT
MODE
LX
FB
PWM
PWM
L1
OUTPUT
VOLTAGE (V)
(GND)
FIXED
OUTPUT
10 H
10
D1
MBR0520L
0.22 F
3.3
3.3
5.0
5.0
Step-Up Converter
0.22 F
Low supply current
high output current
high output current
2 x
100 F
FEATURES
Low noise,
Low noise,
CURRENT (mA)
OUTPUT
R1
R2
ADJUSTABLE
300
750
525
850
OUTPUT
Figure 3. Simplified PWM Controller Block Diagram
the output filter capacitor and load. As the energy
stored in the inductor is depleted, the current ramps
down and the output diode and synchronous rectifier
turn off. Voltage across the load is regulated using
either low-noise PWM or low-power operation, depend-
ing on the CLK/SEL pin setting (Table 2).
When CLK/SEL is pulled high, the MAX1700/MAX1701
operate in a higher power, low-noise pulse-width-
modulation (PWM) mode. During PWM operation, they
switch at a constant frequency (300kHz) and then mod-
ulate the MOSFET switch pulse width to control the
power transferred per cycle and regulate the voltage
across the load. In PWM mode the devices can output
up to 800mA. Switching harmonics generated by fixed-
frequency operation are consistent and easily filtered.
See the Noise Spectrum Plot in the Typical Operating
Characteristics.
During PWM operation, each rising edge of the internal
clock sets a flip-flop, which turns on the N-channel
MOSFET switch (Figure 3). The switch is turned off
when the sum of the voltage-error, slope compensation,
and current-feedback signals trips a multi-input com-
parator and resets the flip-flop; the switch remains off
for the rest of the cycle. When a change occurs in the
output-voltage error signal into the comparator, it shifts
the level to which the inductor current is allowed to
ramp during each cycle and modulates the MOSFET
switch pulse width. A second comparator enforces an
inductor current limit of 1.6A max.
1.3A CURRENT
REF
FB
LIMIT
OSC
Low-Noise PWM Operation
R
S
Q
P
N
POUT
PGND
LX