LM2574HVN-3.3/NOPB National Semiconductor, LM2574HVN-3.3/NOPB Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
LM2574HVN-3.3/NOPB
Manufacturer Part Number
LM2574HVN-3.3/NOPB
Description
IC REG SIMPLE SWITCHER 8-DIP
Manufacturer
National Semiconductor
Series
SIMPLE SWITCHER®r
Type
Step-Down (Buck)r
Datasheet
1.LM2574MX-ADJNOPB.pdf
(24 pages)
Specifications of LM2574HVN-3.3/NOPB
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
3.3V
Current - Output
500mA
Frequency - Switching
52kHz
Voltage - Input
4 ~ 60 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Through Hole
Package / Case
8-DIP (0.300", 7.62mm)
Power - Output
750mW
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*LM2574HVN-3.3
*LM2574HVN-3.3/NOPB
LM2574HVN-3.3
*LM2574HVN-3.3/NOPB
LM2574HVN-3.3
www.national.com
Given:
V
V
I
F = Switching Frequency (Fixed at 52 kHz)
1. Programming Output Voltage (Selecting R1 and R2, as
shown in Figure 2 )
Use the following formula to select the appropriate resistor
values.
R
cient and stability with time, use 1% metal film resistors)
2. Inductor Selection (L1)
A. Calculate the inductor Volt • microsecond constant,
E • T (V • µs), from the following formula:
B. Use the E • T value from the previous formula and match
it with the E • T number on the vertical axis of the Inductor
Value Selection Guide shown in Figure 8 .
C. On the horizontal axis, select the maximum load current.
D. Identify the inductance region intersected by the E • T
value and the maximum load current value, and note the in-
ductor value for that region.
E. Select an appropriate inductor from the table shown in Fig-
ure 3 . Part numbers are listed for three inductor manufactur-
ers. The inductor chosen must be rated for operation at the
LM2574 switching frequency (52 kHz) and for a current rating
of 1.5 x I
ductor section in the application hints section of this data
sheet.
LM2574 Series Buck Regulator Design Procedure
LOAD
OUT
IN
1
PROCEDURE (Adjustable Output Voltage Versions)
(Max) = Maximum Input Voltage
can be between 1k and 5k. (For best temperature coeffi-
(Max) = Maximum Load Current
= Regulated Output Voltage
LOAD
. For additional inductor information, see the in-
FIGURE 8. LM2574HV-ADJ Inductor Selection Guide
14
Given:
V
V
I
F = 52 kHz
1. Programming Output Voltage (Selecting R1 and R2)
R
2. Inductor Selection (L1)
A. Calculate E • T (V • µs)
B. E • T = 185 V • µs
C. I
D. Inductance Region = 1000
E. Inductor Value = 1000 µH Choose from Pulse Engineer-
ing Part # PE-52631, or Renco Part # RL-1283-1000.
LOAD
OUT
IN
2
(Max) = 40V
= 1k (19.51−1) = 18.51k, closest 1% value is 18.7k
LOAD
EXAMPLE (Adjustable Output Voltage Versions)
(Max) = 0.4A
= 24V
(Max) = 0.4A
DS011394-16
(Continued)