HCS320-I/P Microchip Technology, HCS320-I/P Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
HCS320-I/P
Manufacturer Part Number
HCS320-I/P
Description
IC CODE HOPP ENCODER 16FUNC 8DIP
Manufacturer
Microchip Technology
Type
Code Hopping Encoderr
Specifications of HCS320-I/P
Applications
Remote Secure Access, Keyless Entry
Mounting Type
Through Hole
Package / Case
8-DIP (0.300", 7.62mm)
Ic Function
Encoder IC
Supply Voltage Range
3.5V To 13V
Operating Temperature Range
-40°C To +85°C
Digital Ic Case Style
DIP
No. Of Pins
8
Supply Voltage Max
13V
Leaded Process Compatible
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCS320-I/P
Manufacturer:
MICROCHIP
Quantity:
12 000
HCS320
6.0
When using the HCS320 in a system, the user will have
to program some parameters into the device including
the serial number and the secret key before it can be
used. The programming cycle allows the user to input
all 192 bits in a serial data stream, which are then
stored internally in EEPROM. Programming will be
initiated by forcing the PWM line high, after the S2 line
has been held high for the appropriate length of time
line (Table 6-1 and Figure 6-1). After the Program
mode is entered, a delay must be provided to the
device for the automatic bulk write cycle to complete.
This will set all locations in the EEPROM to zeros . The
device can then be programmed by clocking in 16 bits
at a time, using S2 as the clock line and PWM as the
FIGURE 6-1:
FIGURE 6-2:
DS41097C-page 14
(Clock)
(Clock)
Note 1: Unused button inputs to be held to ground during the entire programming sequence.
(Data)
PWM
(Data)
PWM
S2
S2
Note: If a Verify operation is to be done, then it must immediately follow the Program cycle.
End of Programming Cycle
2: The V
PROGRAMMING THE HCS320
Enter Program
Bit190
T
PS
Mode
DD
Bit191
T
PH
pin must be taken to ground after a Program/Verify cycle.
1
PROGRAMMING WAVEFORMS
VERIFY WAVEFORMS
T
PH
T
2
WC
T
PBW
T
Bit 0
Beginning of Verify Cycle
CLKH
Bit 0
T
CLKL
Bit 1
Bit 1 Bit 2
T
Bit 2
DS
T
DV
Repeat for each word (12 times)
T
Bit 3
DH
Data for Word 0 (KEY_0)
Data from Word 0
Bit 3
data in line. After each 16-bit word is loaded, a pro-
gramming delay is required for the internal program
cycle to complete. This delay can take up to T
end of the programming cycle, the device can be veri-
fied (Figure 6-2) by reading back the EEPROM. Read-
ing is done by clocking the S2 line and reading the data
bits on PWM. For security reasons, it is not possible to
execute a verify function without first programming the
EEPROM. A Verify operation can only be done
once, immediately following the Program cycle.
Bit 14
Note:
Bit 14
Bit 15
To ensure that the device does not acci-
dentally enter Programming mode, PWM
should never be pulled high by the circuit
connected to it. Special care should be
taken when driving PNP RF transistors.
Bit 15
T
WC
Bit 16 Bit 17
2001 Microchip Technology Inc.
Bit 16
Data for Word 1
Bit190 Bit191
Bit 17
WC
. At the