RF600E RF Solutions, RF600E Datasheet - Page 6
![IC ENCODER TRANSMITTER RF 8DIP](/photos/7/65/76517/rf600e_sml.jpg)
RF600E
Manufacturer Part Number
RF600E
Description
IC ENCODER TRANSMITTER RF 8DIP
Manufacturer
RF Solutions
Type
Encoderr
Datasheet
1.RF600E.pdf
(24 pages)
Specifications of RF600E
Applications
RF, IR
Mounting Type
Through Hole
Package / Case
8-DIP
Supply Voltage Range
2V To 6.6V
Operating Temperature Range
-55°C To +125°C
Digital Ic Case Style
DIP
No. Of Pins
8
Filter Terminals
SMD
Supply Voltage Max
6.6V
Supply Current
1.6mA
Ic Generic Number
60
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
RF600E
Manufacturer:
RF Solutions
Quantity:
101
DS600-10 March ‘06
Pin Descriptions
Vcc / Vss
The power supply needs to be a stable regulated voltage with <10mV ripple
OP1-4
Digital Data outputs 1-4. These outputs are asserted LOW when the relevant inputs (S0 – S3) on the
RF600E are asserted. (see latch/unlatch information under ‘LKIN’).
LB
The RF600E automatically measures the battery voltage each time it is operated (see RF600E data). This
information is transmitted to the RF600D and if a low battery condition exists then the low battery output is
taken low. This indication is latched until data from a decoder with a good battery is received at which time
the output indication is cleared. (output goes high).
ECS / ECLK / EDAT
These connections are for interface to the EEPROM, which is used to store the identity of the encoders
taught to the system.
ECLK AM / FM Selection
Note that the ECLK output to the EEPROM is also used for data mark selection. The data mark input sets
the input of the RF600D to be compatible with AM or FM radio modulation.
When the ECS control line is low (i.e. when the EEPROM is not selected) the ECLK line is made an input
and a check is made for the presence of a pull-down or pull-up resistor.
If the data mark selection is pull-down then the RF600D will be set to receive Sync Low AM data.
If the data mark selection is pull-up then the RF600D will be set to receive Sync High FM and IR data.
Number
Pin
10
11
12
13
14
15
16
17
18
1
2
3
4
5
6
7
8
9
RF / IR Encoder / Decoder Chipset
RF Evaluation Boards,
Unused
Unused
SLEEP
ECLK
EDAT
Name
LKIN
ECS
LRN
OP3
OP4
SD1
OP1
OP2
Vcc
Vss
Vcc
LB
IN
Output?
In / Out
Input /
©2004 Reg. No. 227 4001, ENGLAND
Out
Out
Out
Out
Out
Out
N/A
N/A
Out
Out
In
In
In
In
In
In
In
Low Battery, goes Low when Low Battery Valid
Connects to EEPROM ‘CS’ pin
Connects to EEPROM ‘CLK’ pin. Also sets data mark.
Serial Data output
Data Output 3 (S2)
Data Output 4 (S3)
Positive supply voltage connection
Connect to GND
Connects to EEPROM ‘Data’ pin
RF / IR Data input
Learn / Erase Switch Input & Status LED Drive
Option Link Input for Momentary or Latched outputs
High = Run, Low = Sleep Mode
Positive supply voltage connection
No Connection
No Connection
Data Output 1 (S0)
Data Output 2 (S1)
Description
Page 6
RF600E
RF600D