MAX1233ETI+ Maxim Integrated Products, MAX1233ETI+ Datasheet - Page 42
![IC CNTRLR TOUCH 28-TQFN](/photos/6/61/66150/28-tqfn_21-0139h_sml.jpg)
MAX1233ETI+
Manufacturer Part Number
MAX1233ETI+
Description
IC CNTRLR TOUCH 28-TQFN
Manufacturer
Maxim Integrated Products
Type
Resistiver
Datasheet
1.MAX1234ETIT.pdf
(44 pages)
Specifications of MAX1233ETI+
Touch Panel Interface
4-Wire
Number Of Inputs/keys
1, 4 x 4 Keypad
Resolution (bits)
8, 10, 12 b
Data Interface
MICROWIRE™, QSPI™, Serial, SPI™
Data Rate/sampling Rate (sps, Bps)
50k
Voltage Reference
External, Internal
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
28-TQFN Exposed Pad
Applications
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
±15kV ESD-Protected Touch-Screen
Controllers Include DAC and Keypad Controller
two 8-bit data streams write the command word into the
MAX1233/MAX1234. The next two 8-bit data streams
can contain either the input or output data.
Using the high-speed QSPI interface (Figure 29) with
CPOL = 0 and CPHA = 0, the MAX1233/MAX1234 sup-
port a maximum f
tions on the serial clock’s falling edge and is clocked
into the µP on the SCLK’s rising edge.
For best performance, use printed circuit boards with
good layouts; do not use wire-wrap boards even for
prototyping. Ensure that digital and analog signal lines
are separated from each other. Do not run analog and
digital (especially clock) lines parallel to one another, or
digital lines underneath the ADC package.
Figure 30 shows the recommended system ground
Figure 29. QSPI Interface
Figure 30. Power-Supply Grounding Connection
42
V
DD
______________________________________________________________________________________
R* = 10Ω
SS
Layout, Grounding, and Bypassing
*OPTIONAL
+3V/+5V
AV
DD
QSPI
SCLK
MAX1233
MAX1234
MISO
MOSI
GND
GND
SCK
CS
SUPPLIES
of 10MHz. DOUT data transi-
DV
DD
CS
SCLK
DOUT
DIN
BUSY
PENIRQ
KEYIRQ
+3V/+5V
V
CIRCUITRY
DD
QSPI Interface
DIGITAL
MAX1233
MAX1234
DGND
connections. Establish a single-point analog ground
(star ground point) at GND. Connect all analog grounds
to the star ground. Connect the digital system ground
to the star ground at this point only. For lowest noise oper-
ation, the ground return to the star ground’s power supply
should be low impedance and as short as possible.
High-frequency noise in the power supply may affect
the high-speed comparator in the ADC. Bypass the
supply to the star ground with a 0.1µF capacitor as
close to pins 1 and 2 of the MAX1233/MAX1234 as
possible. Minimize capacitor lead lengths for best sup-
ply-noise rejection. If the power supply is very noisy, a
10Ω resistor can be connected as a lowpass filter.
While using the MAX1233/MAX1234 with a resistive
touch screen, the interconnection between the convert-
er and the touch screen should be as short and robust
as possible. Since resistive touch screens have a low
resistance, longer or loose connections are a source of
error. Noise can also be a major source of error in
touch-screen applications (e.g., applications that
require a backlight LCD panel). This EMI noise can be
coupled through the LCD panel to the touch screen
and cause “flickering” of the converted data. Utilizing a
touch screen with a bottom-side metal layer connected
to ground couples the majority of noise to ground. In
addition, the filter capacitors from Y+, Y-, X+, and X-
inputs to ground also help reduce the noise further.
Caution should be observed for settling time of the
touch screen.
Integral nonlinearity (INL) is the deviation of the values
on an actual transfer function from a straight line. This
straight line can be either a best-straight-line fit or a line
drawn between the end points of the transfer function,
once offset and gain errors have been nullified. The
static linearity parameters for the MAX1233/MAX1234
are measured using the end-point method.
Differential nonlinearity (DNL) is the difference between
an actual step width and the ideal value of 1LSB. A
DNL error specification of less than 1LSB guarantees
no missing codes and a monotonic transfer function.
Aperture jitter (t
the time between the samples.
Aperture delay (t
falling edge of the sampling clock and the instant when
an actual sample is taken.
AJ
AD
) is the sample-to-sample variation in
) is the time defined between the
Differential Nonlinearity
Integral Nonlinearity
Aperture Delay
Aperture Jitter
Definitions