HCS412-I/P Microchip Technology, HCS412-I/P Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
HCS412-I/P
Manufacturer Part Number
HCS412-I/P
Description
IC CODE HOP ENCODR/TRNSPOND 8DIP
Manufacturer
Microchip Technology
Type
Code Hopping Encoder and Transponderr
Specifications of HCS412-I/P
Applications
Remote Secure Access, Keyless Entry
Mounting Type
Through Hole
Package / Case
8-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
HCS412
2.2.7.2
Connecting an LC resonant circuit between the LC0
and the LC1 pins creates the bi-directional low fre-
quency communication path with the HCS412.
The internal circuitry on the HCS412 provides the fol-
lowing functions:
• LF input amplifier and envelope detector to detect
• 10V zener input protection from excessive
• LF antenna clamping transistors for inductive
• Damping circuitry that improves communication
• Incoming LF energy rectification and regulation
TABLE 2-2:
3.0
3.1
3.1.1
The main way to enter Encoder mode is when the
wake-up circuit detects a button input activation; button
input transition from GND to V
logic wakes and delays a switch debounce time prior to
sampling the button inputs. The button input states,
cumulatively called the button status, determine
whether the HCS412 transmits a code hopping or seed
transmission, Table 3-1.
Additional button activations added during a transmis-
sion will immediately RESET the HCS412, perhaps
leaving the current code word incomplete. The device
will start a new transmission which includes the
updated button code value.
Buttons removed during a transmission will have no
effect unless no buttons remain activated. If no button
activations remain, the minimum number of compete
code words will be completed (Section 3.4.1) and the
device will return to Standby mode.
DS41099C-page 8
and shape the incoming low frequency excitation
signal.
antenna voltage generated when proximate to
very strong magnetic fields.
responses back to the transponder reader. The
antenna ends are shorted together, ‘clamped’,
dissipating the oscillatory energy. The reader
detects this as a momentary load on its excitation
antenna.
when using high-Q LC antenna circuits.
S2LC
0
1
ENCODER OPERATION
Encoder Activation
BUTTON ACTIVATION
TRANSPONDER INTERFACE
• LC1 low frequency antenna output driver for inductive responses and LC bias.
Note: LC0 low frequency antenna input is also enabled.
• S2 button input pin with Schmitt Trigger detector and internal pull-down resistor.
• RFEN output driver.
Note: LC0 and LC1 low frequency antenna interfaces are disabled and the transponder circuitry is
S2/RFEN/LC1 CONFIGURATION OPTION
switched off to reduce standby current.
DD
. The HCS412 control
Resulting S2/RFEN/LC1 Configuration
Preliminary
During normal transponder operation, the LC1 pin func-
tions to bias the LC0 AGC amplifier input. The amplifier
gain control sets the optimum level of amplification in
respect to the incoming signal strength. The signal then
passes through an envelope detector before interpreta-
tion in the logic circuit.
2.2.7.3
When the RF enable (RFEN) configuration option is
enabled, the RFEN signal output is coordinated with
the DATA output pin to provide typical ASK or FSK PLL
activation.
TABLE 2-1:
3.1.2
The other way to enter Encoder mode is if the S2/LC
option is configured for LC operation and the wake-up
circuit detects a signal on the LC0 LF antenna input pin.
This form of activation is called Proximity activation as
a code hopping transmission would be initiated when
the device was proximate to a LF field.
Refer to Section 4.4 for details on configuring the
HCS412 for Proximity Activation.
for the supply voltage in battery-less or low bat-
tery transponder instances.
RFEN
0
1
PROXIMITY ACTIVATION
RF ENABLE OUTPUT
RFEN OPTION
RF Enable output is disabled.
RF Enable output is enabled.
2002 Microchip Technology Inc.
Description