KS8999 Micrel Inc, KS8999 Datasheet - Page 17

• Manufacturer Part Number: KS8999
• Description: IC SWITCH 10/100 9PORT 208PQFP
• Manufacturer: Micrel Inc

Specifications of KS8999

• Applications: *
• Mounting Type: Surface Mount
• Package / Case: 208-MQFP, 208-PQFP
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Phy/transceiver Interface: MII/SNI
• Power Supply Type: Analog/Digital
• Package Type: PQFP
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Mounting: Surface Mount
• Jtag Support: No
• Operating Temperature Classification: Commercial
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: 576-1023 - BOARD EVAL EXPERIMENT FOR KS8999
• Lead Free Status / RoHS Status: Not Compliant, Contains lead / RoHS non-compliant

January 2005
Micrel, Inc.
Group
CTRL
TEST
CFGMODE
I/O Names
LED[7][3]
LED[7][2]
LED[7][1]
LED[7][0]
LED[8][3]
LED[8][2]
LED[8][1]
LED[8][0]
MRXD[3]
MRXD[2]
MRXD[1]
MRXD[0]
SCANEN
MUX[1:2]
MIIS[1:0]
TESTEN
PRSV
AOUT
EN1P
RST#
SDA
SCL
X1
X2
Active Status
Clock
Clock
Clock
I/O
H
H
H
H
H
H
H
H
L
Description
Programs flow control D = No flow control, F/U = Flow control enabled
(default)
Programs broadcast storm protection. D = 5% broadcast frames allowed, F/U
= Unlimited broadcast frames (default)
Programs buffer sharing feature. D = Equal amount of buffers per port (113
buffers), F/U = Share buffers up to 512 buffers on a single port (default)
Reserved – use float configuration
Programs address aging.
D = Aging disabled, F/U = Enable 5 minute aging (default)
Programs frame length enforcement. D = Max length for VLAN is 1522 bytes
and without VLAN is 1518 bytes F/U = Max length is 1536 bytes (default)
Reserved
Programs half-duplex back pressure. D = No half-duplex back pressure,
F/U = Half-duplex back pressure enabled (default)
Programs port 9 speed D = 10Mbps, F/U = 100Mbps (default)
Programs port 9 duplex D = Half-duplex, F/U = Full duplex (default)
Programs port 9 flow control D = Flow control, F/U = No flow control (default)
D = reserved, F/U = normal operation (default)
Enable 802.1p for all ports –this enables QoS based on the priority field in the
layer 2 header.
0 = 802.1p selected by port in EEPROM
1 = Use 802.1p priority field unless disabled in EEPROM
Note: This is also controlled by the EEPROM registers (registers 4-12 bit 4).
The values in the EEPROM supersede this pin. Also, if the priority selection is
unaltered in the EEPROM registers (register 3 bits 0-7) then values above 3
are considered high priority and less than 4 are low priority.
MII mode selection –allows the MII to run in the following modes
MIIS
1 0
0 0
0 1
1 0
1 1
Priority buffer reserve –reserves 6KB of buffer space for the priority traffic if
enabled. 0 = No priority reserve 1 = Reserve 6KB for priority traffic
Note: This is also controlled by the EEPROM registers (register 2 bit 1). The
value in the EEPROM supersedes this pin.
Selects between EEPROM or processor for programming interface.
0 = Processor interface
1 = EEPROM interface or not programmed on this interface (SCL / SDA not
used)
External crystal or clock input
Used when other polarity of crystal is needed. This is unused for a normal
clock input.
Clock for EEPROM
Serial data for EEPROM
System reset
Factory test input –tie low for normal operation
Factory test input –tie low for normal operation
Factory test input –leave open for normal operation
Factory test output –leave open for normal operation
Operating mode
Disable MII interface
Reverse MII
Forward MII
7 wire mode (SNI)
17
KS8999
KS8999