SI8442BB-D-IS Silicon Laboratories Inc, SI8442BB-D-IS Datasheet - Page 25
![IC ISOLATOR 4CH 5.5V 16-SOIC](/photos/7/41/74106/16-soic__7_5mmwidth__sml.jpg)
SI8442BB-D-IS
Manufacturer Part Number
SI8442BB-D-IS
Description
IC ISOLATOR 4CH 5.5V 16-SOIC
Manufacturer
Silicon Laboratories Inc
Series
ISOpror
Datasheet
1.SI8442AB-D-IS.pdf
(38 pages)
Specifications of SI8442BB-D-IS
Number Of Channels
4
Package / Case
16-SOIC (0.300", 7.5mm Width)
Inputs - Side 1/side 2
2/2
Isolation Rating
2500Vrms
Voltage - Supply
2.7 V ~ 5.5 V
Data Rate
150Mbps
Propagation Delay
6ns
Output Type
Tri-State
Operating Temperature
-40°C ~ 125°C
Mounting Style
SMD/SMT
Propagation Delay Time
6 ns
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.7 V
Supply Current
6 mA
Maximum Operating Temperature
+ 125 C
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
336-1765 - KIT EVAL FOR SI84XXISO
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1764-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SI8442BB-D-IS
Manufacturer:
Silicon Laboratories Inc
Quantity:
1 946
Part Number:
SI8442BB-D-IS
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Part Number:
SI8442BB-D-ISR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
3. Errata and Design Migration Guidelines
The following errata apply to Revision C devices only. See "5. Ordering Guide" on page 27 for more details. No
errata exist for Revision D devices.
3.1. Enable Pin Causes Outputs to Go Low (Revision C Only)
When using the enable pin (EN1, EN2) function on the ISOpro 4-channel (Si8440/1/2) isolators, the corresponding
output pin states (pin = An, Bn, where n can be 1…4) are driven to a logic low (to ground) when the enable pin is
disabled (EN1 or EN2 = 0). This functionality is different from the legacy 4-channel (Si8440/1/2) isolators. On those
devices, the isolator outputs go into a high-impedance state (Hi-Z) when the enable pin is disabled (EN1 = 0 or
EN2 = 0).
3.1.1. Resolution
The enable pin functionality causing the outputs to go low is supported in production for Revision C of the ISOpro
devices. Revision D corrects the enable pin functionality (i.e., the outputs will go into the high-impedance state to
match the legacy isolator products). Refer to the Ordering Guide sections of the data sheet(s) for current ordering
information.
3.2. Power Supply Bypass Capacitors (Revision C and Revision D)
When using the ISOpro isolators with power supplies > 4.5 V, sufficient VDD bypass capacitors must be present on
both the VDD1 and VDD2 pins to ensure the VDD rise time is less than 0.5 V/µs (which is > 9 µs for a > 4.5 V
supply). Although rise time is power supply dependent, > 1 µF capacitors are required on both power supply pins
(VDD1, VDD2) of the isolator device.
3.2.1. Resolution
This issue has been corrected with Revision D of the device. Refer to “5. Ordering Guide” for current ordering
information.
3.3. Latch Up Immunity (Revision C Only)
ISOpro latch up immunity generally exceeds ± 200 mA per pin. Exceptions: Certain pins provide < 100 mA of latch-
up immunity. To increase latch-up immunity on these pins, 100 of equivalent resistance must be included in
series with all of the pins listed in Table 14. The 100 equivalent resistance can be comprised of the source
driver's output resistance and a series termination resistor. The Si8441 is not affected when using power supply
voltages (VDD1 and VDD2) < 3.5 V.
3.3.1. Resolution
This issue has been corrected with Revision D of the device. Refer to “5. Ordering Guide” for current ordering
information.
Affected Ordering Part Numbers*
SI8440SV-C-IS/IS1, SI8441SV-C-IS/IS1,
SI8442SV-C-IS/IS1
SI8445SV-C-IS/IS1
*Note: SV = Speed Grade/Isolation Rating (AA, AB, BA, BB).
Table 14. Affected Ordering Part Numbers (Revision C Only)
Revision
Device
C
C
Rev. 1.3
Pin#
10
14
14
6
6
Si8440/41/42/45
Name
EN2
A4
B1
A4
B1
Input or Output
Pin Type
Output
Output
Input
Input
25