IL715-3E NVE, IL715-3E Datasheet - Page 7
![HI-SPD 4CHANN COUPLER 16-SOIC LF](/photos/6/87/68742/390-16-soic__w__sml.jpg)
IL715-3E
Manufacturer Part Number
IL715-3E
Description
HI-SPD 4CHANN COUPLER 16-SOIC LF
Manufacturer
NVE
Series
IsoLoop®r
Datasheet
1.IL717E.pdf
(12 pages)
Specifications of IL715-3E
Inputs - Side 1/side 2
4/0
Number Of Channels
4
Isolation Rating
2500Vrms
Voltage - Supply
3 V ~ 5.5 V
Data Rate
110Mbps
Propagation Delay
12ns
Output Type
Logic
Package / Case
16-SOIC (3.9mm Width)
Operating Temperature
-40°C ~ 100°C
No. Of Channels
4
Supply Current
16µA
Supply Voltage Range
3V To 5.5V
Digital Ic Case Style
SOIC
No. Of Pins
16
Operating Temperature Range
-40°C To +100°C
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
390-1063-5
IL715-3E
Q2264071
IL715-3E
Q2264071
Application Information
Electrostatic Discharge Sensitivity
This product has been tested for electrostatic sensitivity to the
limits stated in the specifications. However, NVE recommends that
all integrated circuits be handled with appropriate care to avoid
damage. Damage caused by inappropriate handling or storage could
range from performance degradation to complete failure.
Electromagnetic Compatibility
IsoLoop Isolators have the lowest EMC footprint of any isolation
technology. IsoLoop Isolators’ Wheatstone bridge configuration
and differential magnetic field signaling ensure excellent EMC
performance against all relevant standards.
These isolators are fully compliant with generic EMC standards
EN50081, EN50082-1 and the umbrella line-voltage standard for
Information Technology Equipment (ITE) EN61000. NVE has
completed compliance tests in the categories below:
EN50081-1
EN50082-2: Industrial Environment
ENV50204
Immunity to external magnetic fields is even higher if the field
direction is “end-to-end” rather than to “pin-to-pin” as shown in the
diagram below:
Dynamic Power Consumption
IsoLoop Isolators achieve their low power consumption from the
way they transmit data across the isolation barrier. By detecting the
edge transitions of the input logic signal and converting these to
narrow current pulses, a magnetic field is created around the GMR
Wheatstone bridge. Depending on the direction of the magnetic
field, the bridge causes the output comparator to switch following
the input logic signal. Since the current pulses are narrow, about
2.5 ns, the power consumption is independent of mark-to-space
ratio and solely dependent on frequency. This has obvious
advantages over optocouplers, which have power consumption
heavily dependent on mark-to-space ratio.
Residential, Commercial & Light Industrial
Methods EN55022, EN55014
Methods EN61000-4-2 (ESD), EN61000-4-3 (Electromagnetic
Field Immunity), EN61000-4-4 (Electrical Transient Immunity),
EN61000-4-6 (RFI Immunity), EN61000-4-8 (Power Frequency
Magnetic Field Immunity), EN61000-4-9 (Pulsed Magnetic
Field), EN61000-4-10 (Damped Oscillatory Magnetic Field)
Radiated Field from Digital Telephones (Immunity Test)
Cross-axis Field Direction
7
Power Supply Decoupling
Both power supplies to these devices should be decoupled with low
ESR 47 nF ceramic capacitors. Ground planes for both GND
GND
Capacitors must be located as close as possible to the V
Signal Status on Start-up and Shut Down
To minimize power dissipation, input signals are differentiated and
then latched on the output side of the isolation barrier to reconstruct
the signal. This could result in an ambiguous output state
depending on power up, shutdown and power loss sequencing.
Therefore, the designer should consider including an initialization
signal in the start-up circuit. Initialization consists of toggling the
input either high then low, or low then high.
Data Transmission Rates
The reliability of a transmission system is directly related to the
accuracy and quality of the transmitted digital information. For a
digital system, those parameters which determine the limits of the
data transmission are pulse width distortion and propagation delay
skew.
Propagation delay is the time taken for the signal to travel through
the device. This is usually different when sending a low-to-high
than when sending a high-to-low signal. This difference, or error, is
called pulse width distortion (PWD) and is usually in nanoseconds.
It may also be expressed as a percentage:
PWD% = Maximum Pulse Width Distortion (ns) x 100%
For example, with data rates of 12.5 Mbps:
PWD% = 3 ns
This figure is almost three times better than any available
optocoupler with the same temperature range, and two times better
than any optocoupler regardless of published temperature range.
IsoLoop isolators exceed the 10% maximum PWD recommended
by PROFIBUS, and will run to nearly 35 Mb within the 10% limit.
Propagation delay skew is the signal propagation difference
between two or more channels. This becomes significant in clocked
systems because it is undesirable for the clock pulse to arrive
before the data has settled. Short propagation delay skew is
therefore especially critical in high data rate parallel systems for
establishing and maintaining accuracy and repeatability. Worst-
case channel-to-channel skew in an IL700 Isolator is only 3 ns,
which is ten times better than any optocoupler. IL700 Isolators
have a maximum propagation delay skew of 6 ns, which is five
times better than any optocoupler.
2
are highly recommended for data rates above 10 Mbps.
80 ns
IL715/IL716/IL717
x 100% = 3.75%
Signal Pulse Width (ns)
DD
pins.
1
and