6N139-000E Avago Technologies US Inc., 6N139-000E Datasheet - Page 12

• Manufacturer Part Number: 6N139-000E
• Description: OPTOCOUPLER DARL-OUT 8-DIP
• Manufacturer: Avago Technologies US Inc.
• Type: Analogr

Specifications of 6N139-000E

• Input Type: DC
• Package / Case: 8-DIP (0.300", 7.62mm)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 60mA
• Data Rate: 100KBd
• Propagation Delay High - Low @ If: 5µs @ 500µA
• Current - Dc Forward (if): 20mA
• Output Type: Open Collector
• Mounting Type: Through Hole
• Isolation Voltage: 3750 Vrms
• Maximum Fall Time: 25 us
• Maximum Rise Time: 60 us
• Minimum Forward Diode Voltage: 1.25 V
• Output Device: Darlington With Base
• Configuration: 1 Channel
• Current Transfer Ratio: 5000 %
• Maximum Baud Rate: 100 KBps
• Maximum Forward Diode Voltage: 1.7 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Input Diode Current: 20 mA
• Maximum Power Dissipation: 135 mW
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Package Type: 8-Pin DIP
• No. Of Channels: 1
• Optocoupler Output Type: Photodarlington
• Input Current: 12mA
• Output Voltage: 18V
• Opto Case Style: DIP
• No. Of Pins: 8
• Ctr Max: 5000%
• Ctr Min: 400%
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 516-1601-5

Package Characteristics
**All typicals at T
†The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage
rating. For the continuous voltage rating refer to the IEC/EN/DIN EN60747-5-2 Insulation Characteristics Table (if applicable), your equipment level
safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage.”
Notes:
1. DC CURRENT TRANSFER RATI0 (CTR) is
2. Pin 7 Open.
3. Device considered a two-terminal device.
4. Use of a resistor between pin 5 and 7 will
5. Common mode transient immunity in a Logic
12
Parameter
Input-Output Momentary
Withstand Voltage†
Resistance (Input-Output)
Capacitance (Input-Output)
defined as the ratio of output collector
current, I
I
Pins 1, 2, 3, and 4 shorted together and Pins
5, 6, 7, and 8 shorted together.
decrease gain and delay time. Significant
reduction in overall gain can occur when
using resistor values below 47 k . For more
information, please contact your local HP
Components representative.
High level is the maximum tolerable
(positive) dV
pulse, V
F
, times 100%.
CM
O
, to the forward LED input current,
, to assure that the output will
CM
A
/dt of the common mode
= 25 C, unless otherwise noted.
Option 020
HCNW139
HCNW138
Sym.
V
R
C
ISO
I-O
I-O
6. In applications where dV/dt may exceed
7. Use of a 0.1 F bypass capacitor connected
8. In accordance with UL 1577, each
remain in a Logic High state (i.e., V
Common mode transient immunity in a Logic
Low level is the maximum tolerable
(negative) dV
pulse, V
remain in a Logic Low state (i.e., V
50,000 V/ s (such as static discharge) a
series resistor, R
protect the detector IC from destructively
high surge currents. The recommended value
is R
between pins 8 and 5 adjacent to the device
is recommended.
optocoupler is proof tested by applying an
insulation test voltage 4500 V rms for 1
second (leakage detection current limit,
3750
5000
Min.
CC
= 220 .
CM
, to assure that the output will
Typ.**
CM
10
0.6
/dt of the common mode
CC
12
, should be included to
Max.
O
O
V rms
Units
< 0.8 V).
> 2.0 V).
pF
RH < 50%, t = 1 min.,
T
V
RH < 45%
f = 1 MHz
A
I-O
= 25 C
9. In accordance with UL 1577, each
Test Conditions
= 500 Vdc
I
100% production test shown in the IEC/EN/
DIN EN 60747-5-2 Insulation Related
Characteristics Table, if applicable.
optocoupler is proof tested by applying an
insulation test voltage > 6000 V rms for 1
second (leakage detection current limit,
I
100% production test for partial discharge
(method b) shown in the IEC/EN/DIN EN
60747-5-2 Insulation Related Characteristics
Table, if applicable.
I-O
I-O
< 5 A). This test is performed before the
< 5 A). This test is performed before the
Fig.
Note
3, 8
3, 9
3
3