HCPL-3140-000E Avago Technologies US Inc., HCPL-3140-000E Datasheet - Page 11
![OPTOCOUPLER IGBT DRIVE 0.4A 8DIP](/photos/7/66/76618/516-8-dip_sml.jpg)
HCPL-3140-000E
Manufacturer Part Number
HCPL-3140-000E
Description
OPTOCOUPLER IGBT DRIVE 0.4A 8DIP
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HCPL-3140-000E.pdf
(16 pages)
Specifications of HCPL-3140-000E
Package / Case
8-DIP (0.300", 7.62mm)
Voltage - Isolation
3750Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
600mA
Propagation Delay High - Low @ If
300ns @ 8mA
Current - Dc Forward (if)
25mA
Input Type
DC
Output Type
Push-Pull, Totem-Pole
Mounting Type
Through Hole
Isolation Voltage
3750 Vrms
Maximum Fall Time
0.05 us
Maximum Forward Diode Current
25 mA
Minimum Forward Diode Voltage
1.2 V
Output Device
Logic Gate Photo IC
Configuration
1 Channel
Maximum Forward Diode Voltage
1.8 V
Maximum Reverse Diode Voltage
5 V
Maximum Power Dissipation
250 mW
Maximum Operating Temperature
+ 100 C
Minimum Operating Temperature
- 40 C
No. Of Channels
1
Optocoupler Output Type
Gate Drive
Input Current
12mA
Output Voltage
30V
Opto Case Style
DIP
No. Of Pins
8
Common Mode Ratio
10 KV/uS
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
516-1583-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCPL-3140-000E
Manufacturer:
AVAGO
Quantity:
40 000
Part Number:
HCPL-3140-000E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
CONTROL
Applications Information
Eliminating Negative IGBT Gate
Drive
To keep the IGBT firmly off,
the HCPL-3140/HCPL-0314 has a
very low maximum V
specification of 1.0 V. Minimizing
Rg and the lead inductance from
the HCPL-3140/HCPL-0314 to
the IGBT gate and emitter
(possibly by mounting the
Figure 19. Recommended LED drive and application circuit for HCPL-3140/HCPL-0314.
11
COLLECTOR
INPUT
+5 V
74XXX
OPEN
270
OL
1
2
3
4
HCPL-3140/HCPL-0314
HCPL-3140/HCPL-0314 on a
small PC board directly above the
IGBT) can eliminate the need for
negative IGBT gate drive in many
applications as shown in
Figure 19. Care should be taken
with such a PC board design to
avoid routing the IGBT collector
or emitter traces close to the
HCPL-3140/HCPL-0314 input as
this can result in unwanted
8
7
6
5
0.1 µF
+
–
V
CC
Rg
= 15 V
Q1
Q2
coupling of transient signals into
the input of HCPL-3140/
HCPL-0314 and degrade
performance. (If the IGBT
drain must be routed near the
HCPL-3140/HCPL-0314 input,
then the LED should be reverse
biased when in the off state, to
prevent the transient signals
coupled from the IGBT drain
from turning on the HCPL-3140/
HCPL-0314.)
3-PHASE
+ HVDC
- HVDC
AC