HCPL-M456#500 Avago Technologies US Inc., HCPL-M456#500 Datasheet - Page 6

• Manufacturer Part Number: HCPL-M456#500
• Description: OPTOCOUPLER IPM 1MBD SO-5
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-M456#500

• Output Type: Open Collector
• Package / Case: 5-SOP
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 15mA
• Propagation Delay High - Low @ If: 200ns @ 10mA
• Current - Dc Forward (if): 25mA
• Input Type: DC
• Mounting Type: Surface Mount
• Configuration: 1 Channel
• Isolation Voltage: 3750 Vrms
• Current Transfer Ratio: 90 %
• Maximum Propagation Delay Time: 550 ns
• Maximum Forward Diode Voltage: 1.8 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Forward Diode Current: 20 mA
• Maximum Continuous Output Current: 15 mA
• Maximum Power Dissipation: 145 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Switching Specifications (R
Over recommended operating conditions unless otherwise specified:
T
*All typical values at 5°C, V
Notes:
10. The difference between t
11. Common mode transient immunity in a Logic High level is the maximum tolerable dV
1. Common mode transient immunity in a Logic Low level is the maximum tolerable dV
13. Pulse Width Distortion (PWD) is defined as |t
6
A
1. Derate linearly above 90°C free-air temperature at a rate of 0.8 mA/°C.
. Derate linearly above 90°C free-air temperature at a rate of 1.6 mA/°C.
3. Derate linearly above 90°C free-air temperature at a rate of 3.0 mW/°C.
4. Derate linearly above 90°C free-air temperature at a rate of 4. mW/°C.
5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current (I
6. Device considered a two-terminal device: Pins 1 and 3 shorted together and Pins 4, 5 and 6 shorted together.
7. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V
8. Pulse: f = 0 kHz, Duty Cycle = 10%.
9. Use of a 0.1 µF bypass capacitor connected between pins 4 and 6 can improve performance by filtering power supply line noise.
Propagation Delay
Time to Low
Output Level
Propagation Delay
Time to High
Output Level
Pulse Width
Distortion
Propagation Delay
Difference Between
Any  Parts
Output High Level
Common Mode
Transient Immunity
Output Low Level
Common Mode
Transient Immunity
= -40°C to +100°C, V
tion current limit, I
fications section.)
the output will remain in a Logic High state (i.e., V
output will remain in a Logic Low state (i.e., V
Parameter
I-O
≤ 5 µA).
CC
CC
PLH
= 15 V.
= +4.5 V to 30 V, I
t
and t
PLH
Symbol
|CM
|CM
PWD
L
t
t
= 20 kΩ)
PHL
PLH
-t
PHL
H
PHL
L
|
|
between any two parts under the same test condition. (See IPM Dead Time and Propagation Delay Speci-
-150
30
70
Min.
15
15
PHL
O
< 1.0 V).
- t
F(on)
PLH
Typ.*
O
00
00
00
100
400
130
30
30
> 3.0 V).
| for any given device.
= 10 mA to 0 mA, V
Max.
450
450
400
550
kV/µs
kV/µs
Units
ns
ns
ns
ns
ns
F(off )
C
I
V
I
V
C
C
C
C
F
F
O
O
L
L
L
L
L
= 0 mA,
= 10 mA,
= 100 pF
> 3.0 V
< 1.0 V
= 100 pF
= 100 pF
= 10 pF
= 10 pF
= -5 V to 0.8 V
CM
CM
/dt of the common mode pulse, V
/dt of the common mode pulse, V
O
Test Conditions
) to the forward LED input current (I
I
V
V
V
V
V
C
V
T
F(on)
CC
CC
CM
F(off )
THLH
THHL
L
A
= 100 pF,
= 5°C
= 15.0 V,
= 15.0 V,
= 1500 V
= 10 mA,
= 0.8 V,
= .0 V,
= 1.5 V
RMS
for 1 second (leakage detec-
P-P
,
CM
CM
, to assure that the
, to assure that
8-1
Fig.
F
6,
) times 100.
7
Note
8, 9
13
10
11
1