1712610000 Weidmuller, 1712610000 Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/7/707/weidmuller_sml.jpg)
1712610000
Manufacturer Part Number
1712610000
Description
HDC-KIT-HA 04.402
Manufacturer
Weidmuller
Series
RockStar®r
Datasheet
1.1802430000.pdf
(340 pages)
Specifications of 1712610000
Kit Type
HDC HA 4-Pole
Values
5 pcs - Bulkhead Enclosure, Cable Gland, Female Insert, Male Insert, Plug Housing
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 28 of 340
- Download datasheet (33Mb)
A
Technical data
Electrical data
Single-phase
2- or 3-wire AC or DC systems
A.18
Design of clearances and creepage distances in electrical equipment,
influencing factors:
Rated voltage
The rated voltage is derived from the nominal voltage of the power supply and the
corresponding network type.
42 / 48 / 50
Rated voltage
of the power
supply (mains)
110 / 120
110-220
120-240
220-440
480-960
24 / 25
1000
30-60
V
100
150
300
600
12.5
220
30
60
**)
**)
**)
**)
**)
**)
*)
For insulation
phase-to-phase
All systems
Voltages for table 4
1000
1000
12.5
100
125
160
250
250
320
500
630
25
32
50
63
63
V
1)
For insulation
phase-to-earth
3-wire systems,
neutr. point earthing
125
250
500
32
V
–
–
–
–
–
–
–
–
–
–
–
–
1)
3-phase
3- or 4-wire AC systems
1) Phase-to-earth insulation levels for unearthed or impedance-earthed
2) For electrical equipment for use in both 3-phase 4-wire and 3-phase
*) It is assumed that the rated voltage of the electrical equipment is not
**) Because of the common changes, the meaning of the ** symbol has
110/120/127
220/230/240
380/400/415
Rated voltage
of the power
supply (mains)
systems are equal to those of phase-to-phase because the operating
voltage to earth of any phase can, in practice, reach full phase-to-phase
voltage. This is because the actual voltage to earth is determined by the
insulation resistance and capacitive reactance of each phase to earth;
thus, a low (but acceptable) insulation resistance of one phase can
earth it and raise the other two to full phase-to-phase voltage to earth.
3-wire supplies, earthed and unearthed, use the values for 3-wire
systems only.
lower than the nominal voltage of the power supply.
not been used in table 1; i.e. the / symbol indicates a 4-wire 3-phase
distribution system. The lower value is the phase-to-neutral voltage,
while the higher value is the phase-to-phase voltage. Where only one
value is indicated, it refers to 3-wire 3-phase systems and specifies
the value phase-to-phase.
The values given in table 1 are still taken into account in tables 3a
and 3b by the ** symbol.
480/500
660/690
720/830
1000**)
150**)
300**)
600**)
V
208
440
575
960
60
*)
phase-to-phase
For insulation
All systems
1000
1000
125
160
200
250
320
400
500
500
630
630
630
800
63
V
Voltages for table 4
3-phase
4-wire systems
with earthed
neutral wire
125
160
250
250
320
400
400
500
630
32
80
V
–
–
–
–
For insulation
phase-to-earth
2)
3-phase
3-wire systems
unearthed
phase-earthed
1000
1000
125
160
200
250
320
400
500
500
630
630
630
800
63
V
1)
or.
Insulating material
The insulating materials are subdivided
into four groups according to their CTI
(Comparative Tracking Index):
Insulating material
I
II
III a
III b
The comparative tracking index must
be determined according to DIN IEC
112/VDE 0303 part 1 on the basis of
specially prepared samples with test
solution A.
600 ≤ CTI
400 ≤ CTI < 600
175 ≤ CTI < 400
100 ≤ CTI < 175