SE-KQP1N Omron, SE-KQP1N Datasheet
![no-image](/images/manufacturer_photos/0/4/494/omron_sml.jpg)
SE-KQP1N
Specifications of SE-KQP1N
Related parts for SE-KQP1N
SE-KQP1N Summary of contents
Page 1
... Case P: Plug-in type None: Flush mount type Note: A 3-phase transformer (sold separately) must be used to operate Plug-in Relays at 380, 400, 415, or 440 VAC. Drop the primary voltage (380 to 440 VAC 200-VAC secondary voltage before applying it to the SE-KP2EN or SE-KQP2EN. Ordering Information SE-@EN Overcurrent operating value: 100% of the current SV ...
Page 2
... A (cosφ = 1.0)/2 A (cosφ = 0.3 to 0.4) at 240 VAC 380/400/440 VAC (cosφ = 1.0)/1.5 A (cosφ = 0.3 to 0.4) at 440 VAC --- (cosφ = 1.0)/2 A (cosφ = 0.3 to 0.4) at 440 VAC Model Inverse type Instantaneous type (See note 1.) SE-KP1N SE-KQP1N SE-KP1AN SE-KQP1AN SE-KP2N SE-KQP2N SE-KP2AN SE-KQP2AN SE-K1N SE-KQ1N SE-K1AN ...
Page 3
... Operates when the current is about 30% of the set current --- Less than 50% of the current SV (at open-phase) At high sensitivity (H): 35 ±10%; At low sensitivity (L): 65 ±10% At high sensitivity (H max.; At low sensitivity (L): 3 ± max. time SV (at a time SV: 1), +10% of max. time SV (at a time SV 10) −5 ...
Page 4
... Time Changeover Switch: ×4 320 280 Time scale value 10 240 200 2 1 160 120 100 200 300 400 500 600 Current (% of current SV) Open-phase Operating Time Characteristics 500 600 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 100 200 300 400 500 600 ...
Page 5
... For example, if the time scale value is 6 and the time changeover switch is set to 4, the operating time Test Button Pushing the test button momentarily operates the trip display and the output relay ...
Page 6
... You cannot use reverse-phase protection if you use control power with single-phase operation. Connect to terminals 1 and 2 for single- phase operation. Also, make sure to turn OFF the reverse-phase setting on the function setting switches. An error will occur if the SE is used with the reverse-phase setting turned ON during single-phase operation. Reverse-phase is detected in order of phase1, phase2 and phase3 of control power ...
Page 7
... M Motor Note: 1. When using the (overload and open-phase) relay not necessary to connect terminal 3 (W). Also, always turn OFF the reverse-phase elements. 2. When using a model with an automatic reset, the Motor Protective Relay may not operate if there is an open phase on the power supply side of the motor circuit. ...
Page 8
... Converter M Motor Note: 1. When using the (overload and open-phase) relay not necessary to connect terminal 3 (W). Also, always turn OFF the reverse-phase elements. 2. When using a model with an automatic reset, the Motor Protective Relay may not operate if there is open phase on the power supply side of the motor circuit 3 ...
Page 9
... Dimensions Note: All units are in millimeters unless otherwise indicated. Plug-in Socket Terminal SE-KP@N, SE-KQP Flush Mount Type SE-K@N, SE-KQ Current Converter SET-3A, SET-3B 26 112 Transformer SE-PT400 (for Use with the SE-K(Q)P2EN 72.0 max. 52 Note: The SE-PT400 can be used for all 200/220/240-VAC SE Relays. ...
Page 10
... Confirm that the relay operates when the current is 50% or less of the current SV. 4. Turn off Reverse-phase 1. Reverse the leads at terminals 2 and 3 of the relay (indi- cated by the dashed lines) to create a reverse-phase condition. 2. Turn on SW and SW 1 ates. ...
Page 11
... Motor circuit is not tripped when the relay oper- ates following the depression of the test button. Relay doesn’t operate properly under light loads. 1. Check each phase for an unbalance of more than 35%, and also check for waveform dis- ■ Calculating the Unbalanced Factor The unbalanced factor can be obtained easily from the following graph ...
Page 12
... CT of the SET-3@ are rectified, then converted to DC voltage, which is necessary for the SE, by the resistor at each tap, and output from the positive and negative terminals. The DC and AC component ratios in this voltage differ between the normal three-phase condition and conditions of phase-failure or unbalance ...
Page 13
... Percentage of current setting DC output voltage (VDC) 8.4 200% 600% Note: 1. This is the output voltage when connected Motor Protective 3.9 to 29.1 2.0 to 8.0 Relay or SAO Current Sensor. When connected to any other model, the output voltages will be about the same as those shown in the 7 ...
Page 14
... Mounting When installing with an 8PFA1 connecting socket, first fasten the socket firmly to the panel with screws, then plug in the relay and secure it with a hook. Leave at least space between the relays for the hooks. Although there is no particular restriction on the mounting direction best to mount horizontally ...
Page 15
... PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability ...