HCMS-3901 Avago Technologies US Inc., HCMS-3901 Datasheet - Page 18
![LED DISPLAY 5X7 4CHAR 3.8MM YLW](/photos/22/51/225177/2210347_sml.jpg)
HCMS-3901
Manufacturer Part Number
HCMS-3901
Description
LED DISPLAY 5X7 4CHAR 3.8MM YLW
Manufacturer
Avago Technologies US Inc.
Series
HCMS-39xxr
Datasheet
1.HCMS-3902.pdf
(18 pages)
Specifications of HCMS-3901
Millicandela Rating
*
Internal Connection
*
Size / Dimension
*
Color
Yellow
Configuration
*
Voltage - Forward (vf) Typ
*
Package / Case
12-DIP
Display Type
Alphanumeric
Number Of Digits/alpha
4
Digit/alpha Size
0.15" (3.8mm)
Character Format
Dot Matrix
Character Size
3.81mm
Led Color
Yellow
Luminous Intensity
148µcd
No. Of Digits / Alpha
4
Display Area Width
17.78mm
Display Area Height
10.16mm
Number Of Digits
4
Illumination Color
Yellow
Wavelength
583 nm
Operating Voltage
5.5 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Common Pin
-
Lead Free Status / Rohs Status
Details
Appendix C. Oscillator
The oscillator provides the internal refresh circuitry
with a signal that is used to synchronize the columns
and rows. This ensures that the right data is in the dot
drivers for that row. This signal can be supplied from
either an external source or the internal source.
A display refresh rate of 100 Hz or faster ensures
flicker-free operation. Thus, for an external oscillator the
frequency should be greater than or equal to 512 x 100 Hz
= 51.2 kHz. Operation above 1 MHz without the prescaler
or 8 MHz with the prescaler may cause noticeable pixel-
to-pixel mismatch.
Appendix D. Refresh Circuitry
This display driver consists of 20 one-of-eight column
decoders and 20 constant current sources, 1 one-of-
eight row decoder and eight row sinks, a pulse width
modulation control block, a peak current control
block, and the circuit to refresh the LEDs. The refresh
counters and oscillator are used to synchronize the
columns and rows.
The 160 bits are organized as 20 columns by 8 rows.
The IC illuminates the display by sequentially turning
ON each of the 8 row-drivers. To refresh the display
once takes 512 oscillator cycles. Because there are
eight row drivers, each row driver is selected for 64
(512/8) oscillator cycles. Four cycles are used to briefly
blank the display before the following row is switched
on. Thus, each row is ON for 60 oscillator cycles out of a
possible 64. This corresponds to the maximum LED on
time.
For product information and a complete list of distributors, please go to our website:
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2010 Avago Technologies. All rights reserved. Obsoletes AV01-0310EN
AV02-0868EN - August 20, 2010
www.avagotech.com
Appendix E. Display Brightness
Two ways have been shown to control the brightness
of this LED display: setting the peak current and setting
the duty factor. Both values are set in Control Word 0.
To compute the resulting display brightness when both
PWM and peak current control are used, simply multiply
the two relative brightness factors. For example, if
Control Register 0 holds the word 1001101, the peak
current is 73% of full scale (BIT D
PWM is set to 60% duty factor (BIT D
BIT D
(.73 x .60 = .44) of full scale.
The temperature of the display will also affect the LED
bright ness as shown in Figure 10.
Appendix F. Reference Material
Application Note 1027: Soldering LED Components
Application Note 1015: Contrast Enhancement Techniques
for LED Displays
Figure 10. Relative luminous Intensity versus ambient temperature
1
= L, BIT D
0
= H). The resulting brightness is 44%
5
=L, BIT D
3
= H, BIT D2 = H,
4
= L) and the