LTL-911VEKSA Lite-On Electronics, LTL-911VEKSA Datasheet
LTL-911VEKSA
Specifications of LTL-911VEKSA
LTL911VEKSA
Related parts for LTL-911VEKSA
LTL-911VEKSA Summary of contents
Page 1
... Selection Guide Part No. LTL911VRKSA LTL911VEKSA LTL911VHKSA LTL911VYKSA LTL912VEKSA LTL912VHKSA LTL912VYKSA Benefits Fewer LEDs Required Lower lighting System Cost Applications Signs and Signals Room Lighting Part No. : LTL911VxKSA/LTL912VxKSA BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Color Φv (lm) Super Red 1.5 Red 2.0 Red-Orange 2.0 Amber 2.0 Red 2 ...
Page 2
... LED materials etc., which allow designers to match the color of popular lighting applications, such as automotive lighting and electronic signs. Devices Part No (LTL*) LTL911VRKSA LTL911VEKSA LTL911VHKSA LTL911VYKSA LTL912VEKSA LTL912VHKSA LTL912VYKSA Part No. : LTL911VxKSA/LTL912VxKSA BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Lens Color Diffusion Water Clear Non-Diffused Water Clear Non-Diffused ...
Page 3
... Package Dimensions NOTES: 1. All dimensions are in millimeters (inches). 2. Protruded resin is 1.0mm(.04") max. 3. Lead spacing is measured where the leads emerge from the package. 4. Specifications are subject change to without notice. Part No. : LTL911VxKSA/LTL912VxKSA BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Page : ...
Page 4
... R Operating Temperature Range Storage Temperature Range LED Junction Temperature Soldering Preheat Temperature Lead Soldering Temperature Notes: 1. Operation at currents below 10mA is not recommended. 2. Derating linear as shown in Fig. 3 Part No. : LTL911VxKSA/LTL912VxKSA BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION =25℃ A Super Red Red 190 190 130 ...
Page 5
... The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Part No. : LTL911VxKSA/LTL912VxKSA BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Part No ...
Page 6
... Typical Electrical / Optical Characteristics Curves (25 Part No. : LTL911VxKSA/LTL912VxKSA BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Ambient Temperature Unless Otherwise Noted) ℃ Page : ...
Page 7
... Bin Code List For Reference Part No. : LTL911VxKSA/LTL912VxKSA BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Page : ...
Page 8
... Packing Spec 1. Tube: 65pcs Dim: 520mm x 9.6mm x 13.3mm 2. Inner carton: 153 tubes x 65 pcs = 9,945 pcs Dim: 530mm x 175mm x 128mm 3. Outer carton: 4 inner cartons x 9,945 pcs = 39,780 pcs Dim: 545mm x 370mm x 280mm Part No. : LTL911VxKSA/LTL912VxKSA BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Page : ...
Page 9
... Soldering time 3 sec. Max. (one time only) Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR re-flow is not suitable process for through whole type Piranha LED production. Part No. : LTL911VxKSA/LTL912VxKSA BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION CAUTIONS ...
Page 10
... Preheat 160 30±5sec (Time 85±15℃(Temp 120 Part No. : LTL911VxKSA/LTL912VxKSA BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Wave Solder Temperature Profile Peak 2.5sec (Time =5sec) max 235℃(Temp =260℃) max =60sec) max =100℃ ...
Page 11
... To verify for ESD damage, check for “light up” and Vf of the suspect LEDs at low currents. The Vf of “good” LEDs should be >2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP product. Part No. : LTL911VxKSA/LTL912VxKSA BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION ...
Page 12
... The appearance and specifications of the product may be modified for improvement, without prior notice. Liteon may make process or materials changes affecting the performance or other characteristics of our products. These products supplied after such changes will continue to meet published specifications, but may not be identical to products supplied as samples or under prior orders. Part No. : LTL911VxKSA/LTL912VxKSA BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION ...