LTL2R3SYK Lite-On Electronics, LTL2R3SYK Datasheet - Page 8

• Manufacturer Part Number: LTL2R3SYK
• Description: LED 5MM 594NM ALINGAP AMBER CLR
• Manufacturer: Lite-On Electronics

Specifications of LTL2R3SYK

• Viewing Angle: 30°
• Package / Case: Radial - 2 Lead
• Color: Amber
• Millicandela Rating: 2800mcd
• Current - Test: 20mA
• Wavelength - Dominant: 590nm
• Wavelength - Peak: 591nm
• Voltage - Forward (vf) Typ: 2.35V
• Lens Type: Clear
• Lens Style/size: Round, 5mm, T-1 3/4
• Height: 8.70mm
• Mounting Type: Through Hole
• Resistance Tolerance: 590nm
• Led Size: T-1 3/4
• Illumination Color: Amber
• Lens Color/style: Water Clear
• Operating Voltage: 2.35 V
• Wavelength: 590 nm
• Luminous Intensity: 2800 mcd
• Operating Current: 20 mA
• Lens Dimensions: 5 mm
• Lens Shape: Dome
• Maximum Operating Temperature: + 80 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: Through Hole
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Luminous Flux @ Current - Test: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 160-1657

1. Application
2. Storage
3. Cleaning
4. Lead Forming & Assembly
5. Soldering
Part No. : LTL2P3SEK / LTL2R3SEK / LTL2P3SYK / LTL2R3SYK
BNS-OD-C131/A4
During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens.
Do not use the base of the lead frame as a fulcrum during forming.
Lead forming must be done before soldering, at normal temperature.
During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress.
When soldering, leave a minimum of 2mm clearance from the base of the lens to the soldering point.
The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity.
It is recommended that LEDs out of their original packaging are used within three months.
For extended storage out of their original packaging, it is recommended that the LEDs be stored in
a sealed container with appropriate desiccant or in desiccators with nitrogen ambient.
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary.
Dipping the lens into the solder must be avoided.
Do not apply any external stress to the lead frame during soldering while the LED is at high temperature.
The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment,
communication equipment and household applications).Consult Liteon’s Sales in advance for information on
applications in which exceptional reliability is required, particularly when the failure or malfunction of the
LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment,
medical and life support systems and safety devices).
Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or
Recommended soldering conditions :
Temperature
Soldering time
catastrophic failure of the LED
Soldering iron
300°C Max.
3 sec. Max.
(one time only)
LITE-ON TECHNOLOGY CORPORATION
CAUTIONS
P r o p e r t y o f L i t e - O n O n l y
Pre-heat
Pre-heat time
Solder wave
Soldering time
Wave soldering
100°C Max.
60 sec. Max.
260°C Max.
10 sec. Max.
Page :
8
of
11