RJ6F502 Copal Electronics Inc, RJ6F502 Datasheet - Page 2

• Manufacturer Part Number: RJ6F502
• Description: POT 5K OHM SINGLE CERMET BOTTOM
• Manufacturer: Copal Electronics Inc
• Series: RJ-6r

Specifications of RJ6F502

• Resistance (ohms): 5K
• Power (watts): 0.5W, 1/2W
• Taper: Linear
• Tolerance: ±10%
• Temperature Coefficient: ±100ppm/°C
• Number Of Turns: Single
• Adjustment Type: Side Adjustment
• Mounting Type: Through Hole
• Resistive Material: Cermet
• Package / Case: Round - 0.413" Dia x 0.299" H (10.50mm x 7.60mm)
• Resistance In Ohms: 5.00K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: RJ-6F502

■
■
■ Specifications are subject to change without notice. Specifications in this catalog are for reference. The formal specification sheets will be submitted upon request.
Rear adjustment
Side adjustment
Top adjustment
Nominal resistance range
Resistance tolerance
Power ratings
Resistance law
Maximum input voltage
Maximum wiper current
Effective electrical angle
End resistance
C.R.V.
Operating temp. range
Temp. coefficient
Insulation resistance
Dielectric strength
Net weight
(
↑
Adjustment
direction)
position
LIST OF PART NUMBERS
ELECTRICAL CHARACTERISTICS
Adjustment
Shape of terminal
(Top view)
1
3
1
1
3
2
2
2
2
2
1
3
3
1
3
DC200 V or power rating, whichever is smaller
10 , 20 , 5 M : 250 10
100 mA or power rating, whichever is smaller
50
A
1 % or 2 , whichever is greater
1 % or 3 , whichever is greater
1000 M minimum (DC500 V)
Form of packaging
Approx. 0.60 g (RJ-6P,W)
Approx. 0.80 g (RJ-6S, X)
Approx. 1.01 g (RJ-6F)
0.5 W (70 °C) 0 W (120 °C)
~ 2 M : 100 10
Plastic bag
RJ-6W
RJ-6P
RJ-6S
RJ-6X
RJ-6F
AC900 V, 60 s
230 ° (1 turn)
10
55 ~ 120 °C
Linear law
10 %
~ 5 M
Pieces in package
-6
/°C maximum
50 pcs./pack
-6
/°C maximum
〈
Fig. 1
The products indicated by A mark are manufactured upon receipt of
order basis.
■
■
Mechanical angle
Operating torque
Stop strength
Rotational life
Terminal to strength
Thrust rotor
Solderability
Thermal shock
Humidity
Shock
Vibration
Load life
Low temp. operation
High temp. exposure
Immersion seal
Soldering heat
A 10
Nominal resistance values
20 k
The above part numbers are all available with the respective combination of
Verify the above part numbers when placing orders.
<Nominal resistance values> (Fig. 1).
Test item
MECHANICAL CHARACTERISTICS
ENVIRONMENTAL CHARACTERISTICS
A 25 k
A 20
50 k
50
Manual soldering : 380 10 °C, 3 ~ 4 s
10 ~ 2000 Hz, 3 directions, 12 times each
260 3 °C, 5 ~ 6 s, two times maximum
6 directions for 3 times each
70 °C, 0.5 W, 1000 h
100 k
10 ~ 65 °C (80 ~ 98 %),
Amplitude 1.52 mm or
100
Acceleration 196 m/s
COPAL ELECTRONICS
65 ~ 125 °C (0.5 h),
Test conditions
Flow soldering :
981 m/s
10 cycles, 240 h
120 °C, 250 h
85 °C, 60 s
55 °C, 2 h
10
500
5 cycles
200 k
200
CERMET TRIMMERS
2
, 6 ms
50 mN·m {510 gf·cm} minimum
~ 200
2~ 15 mN·m {20 ~ 153 gf·cm}
~ 5 M [ Δ R/R ≦
A250 k
10 N {1.02 kgf} minimum
10 N {1.02 kgf} minimum
500
Δ R/R：Change in total resistance
S.S. ：Setting stability
（
245 3 °C, 2 ~ 3 s
2
〉
,
Tensile strength
270 ° (1 turn)
[ Δ R/R ≦
200 cycles
500 k
1 k
No leaks (No continuous bubbles)
{ }
1 M
[ Δ R/R ≦ 1 %]
[ Δ R/R ≦ 1 %]
[ Δ R/R ≦ 1 %]
[ Δ R/R ≦ 2 %]
[ Δ R/R ≦ 1 %]
[ Δ R/R ≦ 2 %]
[ Δ R/R ≦ 1 %]
2 k
Specifications
[S.S. ≦ 1 %]
[S.S. ≦ 1 %]
[S.S. ≦ 1 %]
[S.S. ≦ 2 %]
[S.S. ≦ 2 %]
：
(0.5
(0.5
Reference only
）
RJ-6
2 M
5 k
3 %)]
2 %)]
A 5 M
10 k