NMA1215DC Murata Power Solutions Inc, NMA1215DC Datasheet - Page 3
![CONV DC/DC 1W 12VIN 15V DIP DL](/photos/8/58/85856/nma1215dc_sml.jpg)
NMA1215DC
Manufacturer Part Number
NMA1215DC
Description
CONV DC/DC 1W 12VIN 15V DIP DL
Manufacturer
Murata Power Solutions Inc
Series
NMAr
Type
Isolatedr
Datasheet
1.NMA0512SC.pdf
(6 pages)
Specifications of NMA1215DC
Number Of Outputs
2
Output
±15V
Power (watts)
1W
Mounting Type
Through Hole
Voltage - Input
10.8 ~ 13.2V
Package / Case
14-DIP Module (300 mil, 6 Leads)
1st Output
15 VDC @ 33mA
2nd Output
-15 VDC @ 33mA
Size / Dimension
0.77" L x 0.39" W x 0.27" H (19.6mm x 9.9mm x 6.9mm)
Power (watts) - Rated
1W
Operating Temperature
-40°C ~ 85°C
Efficiency
76%
Approvals
UL
Output Power
0.5 W
Input Voltage Range
10.8 V to 13.2 V
Input Voltage (nominal)
12 V
Output Voltage (channel 1)
+/- 15 V
Output Current (channel 1)
+/- 33 mA
Output Voltage (channel 2)
15 V
Output Current (channel 2)
+/- 33 mA
Isolation Voltage
1 KV
Package / Case Size
DIP
Product
Isolated
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
4th Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
811-1458-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
NMA1215DC
Manufacturer:
MURATAPS
Quantity:
12 000
APPLICATION NOTES
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a specifi ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NMA series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no specifi c agency approvals, such as the NMA series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NMA series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While
parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically
polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We
therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specifi ed test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
RoHS COMPLIANT INFORMATION
www.murata-ps.com
Minimum load
The minimum load to meet datasheet specifi cation is 10% of the full rated load across the specifi ed input voltage range. Lower than 10% minimum loading will result in
an increase in output voltage, which may rise to typically double the specifi ed output voltage if the output load falls to less than 5%.
Capacitive loading and start up
Typical start up times for this series, with a typical input voltage rise time of 2.2μs and output capacitance of 10μF, are shown in the table below. The product
series will start into a capacitance of 47μF with an increased start time, however, the maximum recommended output capacitance is 10μF.
NMA0505xC
NMA0509xC
NMA0512xC
NMA0515xC
NMA1205xC
NMA1209xC
Start-up time
14520
20200
2018
6610
1061
3935
μs
NMA1212xC
NMA1215xC
NMA1505xC
NMA1512xC
NMA1515xC
This series is compatible with RoHS soldering systems with a peak wave solder temperature of
300°C for 10 seconds. The pin termination fi nish on the SIP package type is Tin Plate, Hot Dipped
over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in
this series are backward compatible with Sn/Pb soldering systems.
For further information, please visit www.murata-ps.com/rohs
Start-up time
15980
9765
1060
1627
6275
μs
Technical enquiries email: mk@murata-ps.com, tel: +44 (0)1908 615232
NMA 5V, 12V & 15V Series
Isolated 1W Dual Output DC/DC Converters
Typical Start-Up Wave Form
2010-09-20 KDC_NMA.G01 Page 3 of 6