UWR-12/750-D48A-C Murata Power Solutions Inc, UWR-12/750-D48A-C Datasheet
![CONV DC/DC 12V 750MA SGL A T/H](/photos/8/59/85966/murata__uwr_series_sml.jpg)
UWR-12/750-D48A-C
Specifications of UWR-12/750-D48A-C
Available stocks
Related parts for UWR-12/750-D48A-C
UWR-12/750-D48A-C Summary of contents
Page 1
... Output voltages include 5, 5.2, 12 and 15 Volts. Input voltage ranges are either 4.7-7.25V ("D5A" models), 9-18V ("D12A" models) or 18-75V ("D48A" models). All A-Series UWR models are fully EMI characterized and agency safety approved. A-Series DC/DC’s are extremely reliable, easy-to-use, cost-effective power converters. Use them to improve the reliability of existing equipment or to develop new systems that exceed design objectives ...
Page 2
... UWR-5/1800-D48A-C 5 1800 UWR-5/2000-D12A-C 5 2000 5 2000 UWR-5/2000-D24E-C UWR-5/2000-D48E-C 5 2000 UWR-5.2/1500-D5A-C 5.2 1500 UWR-12/665-D5A-C 12 665 UWR-12/750-D48A-C 12 750 UWR-12/830-D12A-C 12 830 UWR-15/530-D5A-C 15 530 UWR-15/600-D48A-C 15 600 UWR-15/665-D12A-C 15 665 Typical +25°C under nominal line voltage and full-load conditions unless otherwise noted. A Ripple/Noise (R/N) measured over a 20MHz bandwidth. ...
Page 3
... You can, however, use the +Output (pin 3) as ground/ return to effectively reverse the output polarity. Filtering and Noise Reduction All A-Series UWR 6-10 Watt DC/DC Converters achieve their rated ripple and noise specifications without the use of external input/output capaci- tors. In critical applications, input/output ripple and noise may be further reduced by installing electrolytic capacitors across the input terminals and/ or low-ESR tantalum or electrolytic capacitors across the output terminals ...
Page 4
... The performance curves below were derived from actual test data for a single model number (UWR-5/1800-D48A). Since all devices in the 6-10W UWR A-Series have the same circuit topology, the performance curves are representative of all devices Output Voltage vs. Input Voltage and Output Current 5 ...
Page 5
... Input Fusing Certain applications and/or safety agencies may require the installation of fuses at the inputs of power conversion components. For DATEL A-Series UWR 6-10 Watt DC/DC Converters, you should use slow-blow type fuses with values no greater than the following: V Range Fuse Value IN D5A ...
Page 6
... Tokyo, Tel: 3-3779-1031, email: sales_tokyo@murata-ps.com Osaka, Tel: 6-6354-2025, email: sales_osaka@murata-ps.com Shanghai, Tel: +86 215 027 3678, email: shanghai@murata-ps.com Guangzhou, Tel: +86 208 221 8066, email: guangzhou@murata-ps.com Parkway Centre, Tel: +65 6348 9096, email: singapore@murata-ps.com Technical enquiries email: sales@murata-ps.com, tel: MDC_UWR6-10W Series.B03 Page 508 339 3000 ...