MEV3S0505SC Murata Power Solutions Inc, MEV3S0505SC Datasheet - Page 3
![CONV DC/DC 3W 5V IN 5V OUT SIP](/photos/30/8/300819/mev3_sml.jpg)
MEV3S0505SC
Manufacturer Part Number
MEV3S0505SC
Description
CONV DC/DC 3W 5V IN 5V OUT SIP
Manufacturer
Murata Power Solutions Inc
Series
MEV3r
Type
Isolatedr
Specifications of MEV3S0505SC
Number Of Outputs
1
Package / Case
7-SIP Module (4 Leads)
Output
5V
Power (watts)
3W
Mounting Type
Through Hole
Voltage - Input
4.5 ~ 5.5V
1st Output
5 VDC @ 600mA
Size / Dimension
0.77" L x 0.30" W x 0.40" H (19.6mm x 7.6mm x 10.2mm)
Power (watts) - Rated
3W
Operating Temperature
-40°C ~ 85°C
Efficiency
83%
Approvals
UL
Output Power
3 W
Input Voltage Range
4.5 V to 5.5 V
Input Voltage (nominal)
5 V
Output Voltage (channel 1)
5 V
Output Current (channel 1)
600 mA
Isolation Voltage
3 KV
Package / Case Size
SIP
Output Type
Isolated Single
Output Voltage
5 V
Product
Isolated
Output Current
0.6A
Input Voltage
5V
Screening Level
Industrial
Product Height (mm)
10.2mm
Mounting Style
Through Hole
Pin Count
4
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-
4th Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
811-2116-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MEV3S0505SC
Manufacturer:
VICOR
Quantity:
12 000
APPLICATION NOTES
www.murata-ps.com
Minimum load
The minimum load to meet datasheet specifi cation is 10% of the full rated load across the specifi ed input voltage range. Lower than 10% minimum loading will result in
an increase in output voltage, which may rise to typically double the specifi ed output voltage if the output load falls to less than 5%.
Capacitive loading and start up
Typical start up times for this series, with a typical input voltage rise time of 2.2μs and output capacitance of 10μF, are shown in the table below. The product
series will start into a capacitance of 47μF with an increased start time, however, the maximum recommended output capacitance is 10μF.
Ripple & Noise Characterisation Method
Ripple and noise measurements are performed with the following test confi guration.
Differential Mode Noise Test Schematic
C1
C2
C3
R1
R2
T1
RLOAD
Measured values are multiplied by 10 to obtain the specifi ed values.
MEV3S0505SC
MEV3S0509SC
MEV3S0512SC
MEV3S0515SC
MEV3S1205SC
MEV3S1209SC
MEV3S1212SC
MEV3S1215SC
1μF X7R m ultilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC/DC converter
10μF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC/DC converter with an ESR of less
than 100mΩ at 100 kHz
100nF multilayer ceramic capacitor, general purpose
450Ω resistor, carbon fi lm, ±1% tolerance
50Ω BNC termination
3T of the coax cable through a ferrite toroid
Resistive load to the maximum power rating of the DC/DC converter. Connections should be made via twisted wires
Start-up time
1200
165
300
650
200
350
410
75
μs
SUPPLY
DC/DC Converter
Input
+
-
Output
+
-
C1 C2 C3
R LOAD
R1
T1
Typical Start-Up Wave Form
3kVDC Isolated 3W Single Output DC/DC Converters
Technical enquiries email: mk@murata-ps.com, tel: +44 (0)1908 615232
R2
OSCILLOSCOPE
Y INPUT
2010-03-10 KDC_MEV3.B02 Page 3 of 5
MEV3 Series