NMH0515DC Murata Power Solutions Inc, NMH0515DC Datasheet - Page 3
![CONV DC/DC 2W 5VIN 15VOUT DIP DL](/photos/8/65/86596/nmh0515dc_sml.jpg)
NMH0515DC
Manufacturer Part Number
NMH0515DC
Description
CONV DC/DC 2W 5VIN 15VOUT DIP DL
Manufacturer
Murata Power Solutions Inc
Series
NMHr
Type
Isolatedr
Datasheet
1.NMH1215SC.pdf
(6 pages)
Specifications of NMH0515DC
Number Of Outputs
2
Output
±15V
Power (watts)
2W
Mounting Type
Through Hole
Voltage - Input
4.5 ~ 5.5V
Package / Case
14-DIP Module (300 mil, 6 Leads)
1st Output
15 VDC @ 67mA
2nd Output
-15 VDC @ 67mA
Size / Dimension
0.77" L x 0.39" W x 0.30" H (19.6mm x 9.9mm x 7.6mm)
Power (watts) - Rated
2W
Operating Temperature
-40°C ~ 85°C
Efficiency
84%
Approvals
UL
Output Power
2 W
Input Voltage Range
4.5 V to 5.5 V
Input Voltage (nominal)
5 V
Output Voltage (channel 1)
+/- 15 V
Output Current (channel 1)
67 mA
Output Voltage (channel 2)
15 V
Isolation Voltage
1 KV
Package / Case Size
DIP
Output Voltage
+/- 15 V
Product
Isolated
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
4th Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
811-1510-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
NMH0515DC
Manufacturer:
muRataPs
Quantity:
12 000
TECHNICAL NOTES
ISOLATION VOLTAGE
‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage,
applied for a specifi ed time, across a component designed to provide electrical isolation, to verify the integrity of that isolation.
Murata Power Solutions NMH series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second.
A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?”
For a part holding no specifi c agency approvals, such as the NMH series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or
60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part
could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must
be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to
safety standard requirements.
REPEATED HIGH-VOLTAGE ISOLATION TESTING
It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials,
construction and environment. The NMH series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While
parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically
polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We
therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specifi ed test voltage.
This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further
insulation system of physical spacing or barriers.
APPLICATION NOTES
RoHS COMPLIANCE INFORMATION
www.murata-ps.com
Minimum load
The minimum load to meet datasheet specifi cation is 10% of the full rated load across the specifi ed input voltage range. Lower than 10% minimum loading will result in
an increase in output voltage, which may rise to typically double the specifi ed output voltage if the output load falls to less than 5%.
Capacitive loading and start up
Typical start up times for this series, with a typical input voltage rise time of 2.2μs and output capacitance of 10μF, are shown in the table below. The product
series will start into a capacitance of 47μF with an increased start time, however, the maximum recommended output capacitance is 10μF.
NMH0505SC
NMH0509SC
NMH0512SC
NMH0515SC
NMH1205SC
NMH1209SC
NMH1212SC
NMH1215SC
Start-up time
1072
2481
3546
5380
1152
1580
3150
672
μs
NMH2405SC
NMH2409SC
NMH2412SC
NMH2415SC
NMH4805SC
NMH4809SC
NMH4812SC
NMH4815SC
Start-up time
This series is compatible with RoHS soldering systems with a peak wave solder temperature of
300°C for 10 seconds. The pin termination fi nish on the SIP package type is Tin Plate, Hot Dipped
over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in
this series are backward compatible with Sn/Pb soldering systems.
For further information, please visit www.murata-ps.com/rohs
1064
1544
4398
4230
1220
2822
4275
966
μs
Technical enquiries email: mk@murata-ps.com, tel: +44 (0)1908 615232
Isolated 2W Dual Output DC/DC Converters
Typical Start-Up Wave Form
2010-07-09 KDC_NMH.E01 Page 3 of 5
NMH Series