PTH03060WAZ Emerson Network Power, PTH03060WAZ Datasheet - Page 2

• Manufacturer Part Number: PTH03060WAZ
• Description: CONV DC/DC 3.3VIN ADJOUT 10A SMD
• Manufacturer: Emerson Network Power
• Series: PTH03060Wr
• Type: Point of Load (POL) Non-Isolated with UVLOr

Specifications of PTH03060WAZ

• Output: 0.8 ~ 2.5V
• Number Of Outputs: 1
• Power (watts): 25W
• Mounting Type: Surface Mount
• Voltage - Input: 2.95 ~ 3.65V
• Package / Case: 10-DIP SMD Module
• 1st Output: 0.8 ~ 2.5 VDC @ 10A
• Size / Dimension: 1.00" L x 0.62" W x 0.35" H (25.4mm x 15.7mm x 8.9mm)
• Power (watts) - Rated: 25W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 93%
• Approvals: cUL, TUV, UL
• Output Power: 25 W
• Input Voltage Range: 2.95 V to 3.65 V
• Input Voltage (nominal): 3.3 V
• Output Voltage (channel 1): 0.8 V to 2.5 V
• Output Current (channel 1): 10 A
• Package / Case Size: 25.27 mm x 15.75 mm x 9 mm
• Output Voltage: 0.8 V to 2.5 V
• Product: Non-Isolated / POL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 393-1157

Part Number System with Options
N N o o t t e e s s
1
2
3
4
5
6
7
8
9
10
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
DC-DC CONVERTERS
OUTPUT
POWER
(MAX.)
Remote ON/OFF. Positive Logic
ON:
OFF:
See Figure 1 for safe operating curve.
A 330 µF electrolytic input capacitor is required for proper operation. The
capacitor must be rated for a minimum of 700 mA rms of ripple current.
An external output capacitor is not required for basic operation. Adding
330 µF of distributed capacitance at the load will improve the transient
response.
1 A/µs load step, 50 to 100% I
If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point).
The pre-bias start-up feature is not compatible with Auto-Track
because when the module is under Auto-Track
and will sink current if the output voltage is below that of a back-feeding
source. Therefore to ensure a pre-bias hold-off, one of the following two
techniques must be followed when input power is first applied to the
module. The Auto-Track
module’s output held off using the Inhibit pin. Refer to Application Note
154 for more details.
Tape and reel packaging only available on the surface-mount versions.
To order Pb-free (RoHS compatible) surface-mount parts replace the
mounting option ‘S’ with ‘Z’, e.g. PTH03060WAZ. To order Pb-free
(RoHS compatible) through-hole parts replace the mounting option ‘H’
with ‘D’, e.g. PTH03060WAD.
NOTICE: Some models do not support all options. Please contact your
local Artesyn representative or use the on-line model number search tool at
http://www.artesyn.com/powergroup/products.htm to find a suitable
alternative.
25 W
Pin 3 open; or V > Vin - 0.5 V
Pin 3 GND; or V < 0.8 V (min - 0.2 V).
2.95-3.65 Vdc
VOLTAGE
INPUT
™
Mechanical Package
Point of Load Alliance
function must either be disabled, or the
POLA Non-isolated
omax
Product Family
Output Current
Input Voltage
0.8-2.5 Vdc
, C
VOLTAGE
OUTPUT
3 . 3 V i n s i n g l e o u t p u t
Compatible
The ultra-wide output voltage trim range offers major advantages to users who
select the PTH03060. It is no longer necessary to purchase a variety of
modules in order to cover different output voltages. The output voltage can be
trimmed in a range of 0.8 Vdc to 2.5 Vdc. When the PTH03060 converter
leaves the factory the output has been adjusted to the default voltage of 0.8 V.
PTH03060
03 = 3.3 V
out
06 = 10 A
Always 0
= 330 µF.
O O u u t t p p u u t t V V o o l l t t a a g g e e A A d d j j u u s s t t m m e e n n t t o o f f t t h h e e P P T T H H 0 0 3 3 0 0 6 6 0 0 S S e e r r i i e e s s
™
control, it is fully active
CURRENT
OUTPUT
(MIN.)
P T H 0 3 0 6 0 W A S T
0 A
™
. This is
CURRENT
OUTPUT
(MAX.)
10 A
EFFICIENCY
(MAX.)
93%
OUTPUT VOLTAGE
EFFICIENCY TABLE (I
Vo = 1.0 V
Vo = 1.2 V
Vo = 1.5 V
Vo = 1.8 V
Vo = 2.0 V
Vo = 2.5 V
Packaging Options
No Suffix = Trays
T = Tape and Reel
Mounting Option
D = Horizontal Through-Hole (Matte Sn)
H = Horizontal Through-Hole (Sn/Pb)
S = Surface-Mount (63/37 Sn/Pb
Z = Surface-Mount (95.5/3.8/0.7 Sn/Ag/Cu
Pin Option
A = Through-Hole Std. Pin Length (0.140”)
A = Surface-Mount Tin/Lead Solder Ball
Output Voltage Code
W = Wide
±10 mV
LINE
pin solder material)
pin solder material)
REGULATION
File Name: pth03060.pdf Rev: 28 Jun 2006
EFFICIENCY
±12 mV
O
LOAD
(9)
(8)
= 7 A)
85%
87%
89%
91%
92%
93%
NEW Product
NUMBER
PTH03060
MODEL
(9,10)
2