LTM8027IV#PBF Linear Technology, LTM8027IV#PBF Datasheet - Page 9
![IC BUCK SYNC ADJ 4A 113LGA](/photos/8/70/87009/113_lga_05-08-1756_sml.jpg)
LTM8027IV#PBF
Manufacturer Part Number
LTM8027IV#PBF
Description
IC BUCK SYNC ADJ 4A 113LGA
Manufacturer
Linear Technology
Series
µModuler
Type
Point of Load (POL) Non-Isolatedr
Datasheet
1.LTM8027MPVPBF.pdf
(22 pages)
Specifications of LTM8027IV#PBF
Design Resources
LTM8027 Spice Model
Output
2.5 ~ 24 V
Number Of Outputs
1
Power (watts)
96W
Mounting Type
Surface Mount
Voltage - Input
4.5 ~ 60 V
Package / Case
113-LGA
1st Output
2.5 ~ 24 VDC @ 4A
Size / Dimension
0.59" L x 0.59" W x 0.17" H (15mm x 15mm x 4.32mm)
Power (watts) - Rated
96W
Operating Temperature
-40°C ~ 125°C
Efficiency
95%
Primary Input Voltage
60V
No. Of Outputs
1
Output Voltage
24V
Output Current
4A
No. Of Pins
113
Operating Temperature Range
-40°C To +125°C
Voltage Regulator Type
Buck DC/DC Converter
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
PIN FUNCTIONS
V
internal regulator and to the internal power switch. These
pins must be locally bypassed with an external, low ESR
capacitor (see Table 2).
V
capacitor and the output load between these and the GND
pins.
AUX (Pin A7): Low Current Voltage Source for BIAS1and
BIAS2. In many designs, the BIAS pins are simply connected
to V
is placed near the BIAS pins to ease printed circuit board
routing. Although this pin is internally connected to V
do NOT connect this pin to the load. If this pin is not tied
to BIAS1 and BIAS2, leave it floating.
BIAS1 (Pin A6): The BIAS1 pin connects to the internal
power bus. Connect to a power source greater than 8.5V.
If the output is greater than 8.5V, connect it to this pin. If
the output voltage is less, connect this to a voltage source
between 8.5V and 15V.
BIAS2 (Pin A3): Internal Biasing Power. Connect to AUX
(if 24V or less) or a voltage source above 6V. Do not leave
BIAS2 floating.
RUN (Pin A4): Tie the RUN pin to ground to shut down the
LTM8027. Tie to 1.4V or more for normal operation. The
RUN pin is internally clamped to 5V, so when it is pulled
up, be sure to use a pull-up resistor that limits the cur-
rent in to the RUN pin to less than 1mA. If the shutdown
feature is not used, tie this pin to the V
pull-up resistor.
IN
OUT
(Bank 3): The V
OUT
(Bank 1): Power Output Pins. Apply the output filter
. The AUX pin is internally connected to V
IN
pins supply current to the LTM8027’s
IN
pin through a
OUT
OUT
and
,
GND (Bank 2): Tie these GND pins to a local ground plane
below the LTM8027 and the circuit components.
RT (Pin B1): The RT pin is used to program the switching
frequency of the LTM8027 by connecting a resistor from
this pin to ground. The Applications Information section of
the data sheet includes a table to determine the resistance
value based on the desired switching frequency. Minimize
capacitance at this pin.
SYNC (Pin C1): The SYNC pin provides an external clock
input for synchronization of the internal oscillator. The R
resistor should be set such that the internal oscillator fre-
quency is 10% to 25% below the external clock frequency.
This external clock frequency must be between 100kHz and
500kHz. If unused, the SYNC pin is connected to GND. For
more information see Oscillator Sync in the Application
Information section of this data sheet.
ADJ (Pin A2): The LTM8027 regulates its ADJ pin to 1.23V.
Connect the adjust resistor from this pin to ground. The
value of R
where R
SS (Pin A5): The soft-start pin is used to program the
supply soft-start function. Use the following formula to
calculate C
The pin should be left unconnected when not using the
soft-start function.
R
C
SS
ADJ
= 2µA(t
= 613.77/(V
ADJ
ADJ
SS
is in kΩ.
for a given output voltage slew rate:
is given by the equation:
SS
/1.231V)
OUT
– 1.23)
LTM8027
8027fa
9
T