LSN-T/10-D12N-C Murata Power Solutions Inc, LSN-T/10-D12N-C Datasheet - Page 3

• Manufacturer Part Number: LSN-T/10-D12N-C
• Description: CONV DC/DC 10A 0.75-5.25V SIP
• Manufacturer: Murata Power Solutions Inc
• Type: Point of Load (POL) Non-Isolatedr
• Series: LSNr

Specifications of LSN-T/10-D12N-C

• Number Of Outputs: 1
• Output: 0.75 ~ 5.25V
• Power (watts): 51W
• Mounting Type: Through Hole
• Voltage - Input: 10 ~ 14V
• Package / Case: 11-SIP Module (10 Leads)
• 1st Output: 0.75 ~ 5.25 VDC @ 10A
• Size / Dimension: 2.00" L x 0.34" W x 0.55" H (50.8mm x 8.6mm x 14mm)
• Power (watts) - Rated: 51W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 96.5%
• Approvals: EN, UL
• Output Power: 53 W
• Input Voltage Range: 10.8 V to 13.2 V
• Input Voltage (nominal): 12 V
• Output Voltage (channel 1): 1.2 V to 5.25 V
• Output Current (channel 1): 10 A
• Package / Case Size: SIP
• Output Type: Low Voltage
• Output Voltage: 0.75 V to 5.25 V
• Input Voltage: 10V To 14V
• Power Rating: 51W
• Output Current: 10A
• Supply Voltage: 12V
• Dc / Dc Converter Case Style: SIP
• Dc/dc Converter Mounting: Through Hole
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Product: Non-Isolated / POL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 811-1808-5

Performance/Functional Specifications
Typical @ T
Input
Output
Dynamic Characteristics
Environmental
Physical
Input Voltage Range
Input Current:
Input Reflected Ripple Current
Input Filter Type
Overvoltage Protection
Reverse-Polarity Protection
Start-up Voltage
Undervoltage Shutdown
On/Off Control
On/Off Current
Maximum Output Power
V
Minimum Loading
Maximum Capacitive Load
V
Ripple/Noise (20MHz BW)
Extreme Accuracy
Efficiency
Pre-Bias Startup
Overcurrent Detection and Short-Circuit Protection:
Transient Response (50-100-50% load) 50μsec to ±2% of final value
Start-Up Time:
Switching Frequency:
Calculated MTBF
Operating Temperature: (Ambient)
Storage Temperature
Thermal Shutdown
Dimensions
Pin Dimensions/Material
Weight
Flamability Rating
OUT
OUT
Normal Operating Conditions
Inrush Transient
Standby/Off Mode
Output Short-Circuit Condition
Positive Polarity (no suffix)
Negative Polarity
Current-Limit Inception
Short-Circuit Detection Point
SC Protection Technique
Short-Circuit Current
V
Without Derating (Natural convection) –40 to +85°C
With Derating
IN
Trim Range
to V
Accuracy (50% load)
Cold Condition
A
OUT
= +25°C under nominal line voltage, V
and On/Off to V
OUT
10-14 Volts (12V nominal)
See Ordering Guide
0.02A
5mA
60mA average
30mAp-p
Capacitive
None
None
9.2 Volts
8 Volts
On = Pin open to +V
Off = Zero (ground) to +0.8V max.
On = Pin open or grounded to +0.3V
Off = +2.5V to +V
0.5 mA maximum
51 Watts
±2%
No minimum load
2,000μF (ESR < 0.02 Ohms)
10,000μF (ESR > 0.02 Ohms)
+0.7525 to +5.5 Volts (no load)
See Ordering Guide
3% max. over line/load/temperature
See Ordering Guide
Converter will start up if the external output
voltage is less than Vsetpoint
21 Amps
98% of V
Hiccup with auto recovery
400mA average
8msec
250 ±30 KHz
TBC
See Derating Curves
-40 to +125°C
+115°C
See Mechanical Specifications
0.03" (0.76mm) dia. round copper with
tin plate over nickel underplate.
Length: 0.17” (4.32mm)
0.3 ounces (8.5g)
UL94V-0
OUT
2
=5V, and full-load conditions unless noted.
sec
O U T
set
www.murata-ps.com
IN
max.
IN
max.
Single Adjustable Output, Non-isolated, 12Vin, 10A, SIP, DC/DC Converters
Absolute Maximum Ratings
These are stress ratings. Exposure of devices to any of these conditions may adversely
affect long-term reliability. Proper operation under conditions other than those listed in
the Performance/Functional Specifications Table is not implied.
Input Voltage:
On/Off Control (Pin 11)
Input Reverse-Polarity Protection
Output Overvoltage Protection
Output Current
Storage Temperature
Lead Temperature (soldering, 10 sec.)
All models are tested and specified with external 22μF tantalum input and 10 || 1μF output
capacitors.These capacitors are necessary to accommodate our test equipment and may not
be required to achieve specified performance in your applications. All models are stable and
regulate within spec under no-load conditions.
See Technical Notes and Performance Curves for details.
The On/Off Control (pin 11) is designed to be driven with open-collector logic or the appli-
cation of appropriate voltages (referenced to Common, pins 5 and 6).
Output noise may be further reduced with the installation of additional external output
filtering. See I/O Filtering and Noise Reduction.
MTBF’s are calculated using Telcordia SR-332(Bellcore), ground fixed, T
power, natural convection.
Do not exceed maximum rated output power when adjusting the output voltage.
Continuous or transient
Technical enquiries email: [e-mail], tel:
14 Volts
+V
None
None
Current limited. Devices can
withstand sustained output short
circuits without damage.
–40 to +125°C
+280°C
LSN-T/10-D12
IN
LSN-T10-D12.B01 Page 3 of 12
A
= +25°C, full
[phone]