LSN2-T/16-D12N-C Murata Power Solutions Inc, LSN2-T/16-D12N-C Datasheet - Page 12
![CONV DC/DC 80W 16A 0.75-5V SIP](/photos/8/72/87284/lsn2-t_16-d12n-c__side_1__sml.jpg)
LSN2-T/16-D12N-C
Manufacturer Part Number
LSN2-T/16-D12N-C
Description
CONV DC/DC 80W 16A 0.75-5V SIP
Manufacturer
Murata Power Solutions Inc
Series
LSN2r
Type
Point of Load (POL) Non-Isolatedr
Datasheet
1.LSN2-T10-W3N-C.pdf
(15 pages)
Specifications of LSN2-T/16-D12N-C
Number Of Outputs
1
Output
0.75 ~ 5V
Power (watts)
80W
Mounting Type
Through Hole
Voltage - Input
8.3 ~ 14V
Package / Case
12-SIP Module
1st Output
0.75 ~ 5 VDC @ 16A
Size / Dimension
2.00" L x 0.32" W x 0.50" H (50.8mm x 8.1mm x 12.7mm)
Power (watts) - Rated
80W
Operating Temperature
-40°C ~ 85°C
Efficiency
94%
Approvals
CSA, EN, UL
Output Power
80 W
Input Voltage Range
8.3 V to 14 V
Input Voltage (nominal)
12 V
Output Voltage (channel 1)
0.75 V to 5 V
Output Current (channel 1)
16 A
Package / Case Size
SIP
Output Type
Low Voltage Selectable
Output Voltage
0.75 V to 5 V
Product
Non-Isolated / POL
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
811-1805-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LSN2-T/16-D12N-C
Manufacturer:
Murata Power Solutions Inc
Quantity:
135
Circuits
The circuits shown in Figures 12 through 14 introduce several concepts when
using these Sequencing controls on Point-of-Load (POL) converters. These
circuits are only for reference and are not intended as fi nal designs ready for
your application. Also, numerous connections are omitted for clarity.
the POL B ramps up identically to POL A as shown in timing diagram, Figure
8. RC network R1 and C1 charge up at a rate set by the R1-C1 time constant,
giving a roughly linear ramp. As POL A reaches 3.3V
B), POL B will stop rising. POL A then continues rising until it reaches 5V. R1
should be signifi cantly smaller than the internal bias current resistor from the
Sequence pin. Start with a 20k: value. We assume that the critical phase is
only on power up therefore there is no provision for ramped power down.
added a FET at Q1 as an up/down control. When V
POL, Q1 is biased on, shorting out the Sequence pin. When Q1’s gate is biased
off, R1 charges C1 and the POL’s output ramps up at the R1-C1 slew rate.
Note: Q1’s gate would typically be controlled from some external digital logic.
Figure 12 shows a basic Master (POL A) and Slave (POL B) connected so
Figure 13 shows a single POL and the same RC network. However, we have
Figure 12. Wiring for Simultaneous Phasing
Figure 13. Self-Ramping Power Up
IN
OUT
power is applied to the
(the setpoint of POL
www.murata-ps.com
small resistor in series with Q1’s drain.
ing divider (R2 and R3) on POL B. We have also added an optional very small
noise fi lter cap at C2. Figure 14’s circuit corresponds roughly to Figure 9’s
timing for power up.
Guidelines for Sequence/Track Applications
[1] Leave the converter’s On/Off Enable control (if installed) in the On setting.
[2] Allow the converter to stabilize (typically less than 20 mS after +V
[3] If you do not use the Sequence/Track pin, leave it open or tied to +V
[4] Observe the Output slew rate relative to the Sequence input. A rough
[5] Be aware of the input characteristics of the Sequence pin. The high
If you wish to have a ramped power down (rather than a step down), add a
Figure 14 shows both a RC ramp on Master POL A and a proportional track-
Normally, you should just leave the On/Off pin open.
power on) before raising the Sequence input. Also, if you wish to have a
ramped power down, leave +V
not simply shut off power.
guide is 2 Volts per millisecond maximum slew rate. If you exceed
this slew rate on the Sequence pin, the converter will simply ramp up
at it’s maximum output slew rate (and will not necessarily track the
faster Sequence input). The reason to carefully consider the slew rate
limitation is in case you want two different POL’s to precisely track
each other.
input impedance affects the time constant of any small external ramp
capacitor. And the bias current will slowly charge up any external caps
over time if they are not grounded. The internal pull-up resistor to +V
typically 400k: to 1M:.
Figure 14. Proportional Phasing
Selectable-Output DC/DC Converters
25 Jun 2010
Non-isolated, DOSA-SIP, 6/10/16A
IN
powered all during the down ramp. Do
LSN2 Series
MDC_LSN2.B07Δ
email: sales@murata-ps.com
Page 12 of 15
IN
IN
IN
.
is