MPDTH03050WAH Murata Electronics North America, MPDTH03050WAH Datasheet - Page 11

• Manufacturer Part Number: MPDTH03050WAH
• Description: CONV DC/DC 15W .8-2.5VOUT 6A
• Manufacturer: Murata Electronics North America
• Series: MPDr
• Type: Point of Load (POL) Non-Isolatedr

Specifications of MPDTH03050WAH

• Output: 0.8 ~ 2.5V
• Number Of Outputs: 1
• Power (watts): 15W
• Mounting Type: Through Hole
• Voltage - Input: 2.95 ~ 3.65V
• Package / Case: 6-DIP Module
• 1st Output: 0.8 ~ 2.5 VDC @ 6A
• Size / Dimension: 0.87" L x 0.49" W x 0.33" H (22.1mm x 12.6mm x 8.5mm)
• Power (watts) - Rated: 15W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 94%
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Other names: 490-5067; MPDTH03050WAH

1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
16. ! Note
Note:
15. 3 Storage
15. 4 Operational Environment and Operational Conditions
15. 5 Transportation
2. All the items and parameters in this product specification have been prescribed on the premise that Murata’s
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
specifications or transact the approval sheet for product specifications before ordering.
1. Murata recommends that customers ensure that the evaluation and testing of these devices are completed
15. 3. 1 This product should be treated as MSL2 product when it is reflowed according to
15. 3. 2 Murata recommends that this device not be stored under conditions such as:
15. 4. 1 Operational Environment
15. 4. 2 Operational Conditions
product is used for the purpose, under the condition and in the environment mutually agreed upon.
15. 4. 3 Note prior to use
with this product actually assembled on their product.
Murata recommends that when transporting this product, it be packed so as to avoid damage by mechanical
vibration or exposure to adverse conditions such as ocean air, high humidity. It is additionally recommended
that appropriate instructions and guidelines be communicated to carriers to prevent exposure to these same
conditions.
containing a corrosive gas (e.g., Cl2, NH3, SO2, NOX, etc.).
If stored for over 1 year, baking of this device before soldering is recommended.
If devices are baked in the manufacturer’s tray or in manufacturer’s tape, 60±5
recommended.
Please avoid dampness and heat or locations where temperatures may vary widely to avoid possible water
condensation on the device. Exposure to such environments may degrade the performance and/ or the
reliability of the device.
Please use this product within specified values (power supply, temperature, input, output and load condition,
and so on). If the device is exposed to conditions outside of the specified values reliability of the device may
be adversely affected.
Exposure of this device to a high-level static charge, over-rated voltage, or reverse voltage may result in
diminished reliability and/ or failure. Murata recommends that the following conditions be avoided prior to
use of this device:
This product can be stored for up to 1 year at below 30
process.
The recommended baking condition of individual devices is 125±5
regularly to confirm material degradation has not occurred.
a location where surfaces have an accumulation of dust, direct exposure to ocean air, or in an atmosphere
recommended soldering conditions described in section 15.1.3. .
If the device must be stored for a longer time than 1 year it is recommend that solderability be tested
This device is not water-, chemical- or corrosion-proof.
In order to prevent leakage of electricity and abnormal temperature rise of the device,
do not operate under the following environmental conditions:
(1) Supply of power outside of rated value (see section 8), Supply of reverse power or inadequate
(2) Electrostatic discharge from production line and/or operator
(3) Electrification of the device from electrostatic induction
(1) An atmosphere containing corrosive gas (Cl2, NH3, SO2, NOX, and so on)
(2) A high-dust environment
(3) Under the exposure of direct sunlight
(4) A location where the likelihood of exposure to water or water condensation exists.
(5) A location exposed to ocean air
(6) Any locations similar to the above
connection of a 0V (DC) line
In addition Murata recommends that excessive mechanical shock be avoided.
This document is subject to revision without prior or subsequent notice.
Please contact Murata for latest documentation
o
C 60%R.H., without requiring an additional baking
o
C/24hour.
o
C/168hour is
MPDTH03050WA* Specification
2006.10.2
11