MPDTH03060WAS Murata Electronics North America, MPDTH03060WAS Datasheet - Page 4

• Manufacturer Part Number: MPDTH03060WAS
• Description: CONV DC/DC 25W .8-2.5VOUT 10A
• Manufacturer: Murata Electronics North America
• Series: MPDr
• Type: Point of Load (POL) Non-Isolatedr

Specifications of MPDTH03060WAS

• Output: 0.8 ~ 2.5V
• Number Of Outputs: 1
• Power (watts): 25W
• Mounting Type: Surface Mount
• Voltage - Input: 2.95 ~ 3.65V
• Package / Case: 10-DIP SMD Module
• 1st Output: 0.8 ~ 2.5 VDC @ 10A
• Size / Dimension: 0.99" L x 0.62" W x 0.38" H (25.3mm x 15.8mm x 9.6mm)
• Power (watts) - Rated: 25W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 93%
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Other names: 490-5072; MPDTH03060WAS

1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
Note:
(*1) See SOA curves or consult factory for appropriate derating.
(*2) The minimum input voltage is equal to 2.95V or Vout+0.65V, whichever is greater.
(*3) The set-point voltage tolerance is affected by the tolerance and stability of Rset. The stated limit is
(*4) The peak-to-peak output ripple voltage is measured with an external 10µF ceramic capacitor.
(*5) This control pin has an internal pull-up. If it is left open-circuit the module will operate when input power is
(*6) The external input capacitor must have a ripple current rating at or above 500mA rms.
(*7) An external output capacitor is not required for basic operation. Adding 330µF of distributed capacitance at
9 .2 Safe Operating Area (SOA)
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
specifications or transact the approval sheet for product specifications before ordering.
External Input Capacitor
Switching Frequency
I
the load however will improve transient response.
unconditionally met if Rset has a tolerance of +/-1% with 100ppm/
applied.
The above SOA represents the condition at which internal components are at or below the manufacturer’s
maximum operating temperatures. Derating limits apply to modules soldered directly to a 4 in.×4in. 4-layer
PCB with 1 oz. copper. For more reliable operation, appropriate derating is desirable.
External Output
Inhibit Control
Inhibit Control
Inhibit Control
Inhibit Control
t Hi h V lt
Capacitor
MTBF
Item
90
80
70
60
50
40
30
20
0
IIL inhibit
Symbol
MTBF
Iin inh
Cout
VIH
VIL
Frq
Cin
MPDTH03060W Safe Operating Area
2
Referenced to GND
Referenced to GND
Pin to GND
Inhibit to GND, Track open
Over Vin and Io Ranges
Non-Ceramic (ESR≧4mΩ)
Ceramic
Per Bellcore TR-332, 50% Stress,
Ta=40
4
Iout - Amps
(Vout=2.5V)
o
C, Ground Benign
6
Condition
8
10
o
C or better temperature stability.
This pin should left open to
operate (*5)
Min.
-0.2
330
(*6)
5.7
0
0
-
-
-
400LFM
200LFM
100LFM
Nat Conv
Value
-130
Typ.
300
330
(*7)
10
-
-
-
-
MPDTH03060WA* Specification
Max.
5500
300
0.6
-
-
-
-
-
10
Unit
kHz
mA
µA
µF
µF
６
V
Hrs
2006.10.2
4