SRBA-06A2ALG Bel Fuse Inc, SRBA-06A2ALG Datasheet
SRBA-06A2ALG
Specifications of SRBA-06A2ALG
Related parts for SRBA-06A2ALG
SRBA-06A2ALG Summary of contents
Page 1
... Active Low/High Description The Bel SRBA-06A2Ax modules are a series of non-isolated dc/dc converters that deliver output current with full load efficiency of 92% at 5.0 Vdc output. These modules provide precisely regulated voltage programmable via external resistor from 0.75 Vdc to 5.5 Vdc over a wide range of input voltage (8.3 Vdc - 14 Vdc) ...
Page 2
... Ripple and Noise (rms) Vo=5.0 V Turn on Time Overshoot at Turn on Output Capacitance ESR ≥ 1 mohm ESR ≥ 10 mohm Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 0.75 Vdc - 5.5 Vdc/6 A Output Min Typ 8 ...
Page 3
... V Calculated Per Bell Core SR-332 ( °C) Nominal Notes SRBA-06A2A0; Remote On/Off pin open, Unit on. SRBA-06A2AL; Remote On/Off pin open, Unit on. Sequencing Voltage applied on SEQ pin should be higher than output voltage. Delay from Vin, min to application of voltage on SEQ pin = O ...
Page 4
... Equation for calculating the trim voltage (in V) given the desired adjusted voltage (Vadj) is shown below. The Trim Up voltage should be connected between the Trim pin and Ground. = − 0667 trim Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 0.75 Vdc - 5.5 Vdc/6 A Output − 1 × − 7525 ...
Page 5
... OUTPUT CURRENT MODULE 1.2V 90.0% 80.0% 70.0% 60.0% 50. OUTPUT CURRENT Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 0.75 Vdc - 5.5 Vdc/6 A Output 8.3V 12.0V 14.0V 6A 8.3V 12.0V 14. 90.0% 80.0% 8.3V 12 ...
Page 6
... NON-ISOLATED DC/DC CONVERTERS 8.3 Vdc - 14 Vdc Input Thermal Derating Curves Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 0.75 Vdc - 5.5 Vdc/6 A Output Vin=12 V, Vo=0.75 V Vin=12 V, Vo=2.5 V Vin=12 V, Vo=5.0 V ...
Page 7
... Note: The output ripple and noise is tested at 0-20 MHz BW, 10 uF/10 V tantalum capacitor and 1 uF/10 V ceramic capacitor, Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 0.75 Vdc - 5.5 Vdc/6 A Output Ripple and noise at full load, Vin=12 V, Vo=1 ...
Page 8
... Vin=12 V, Vo=1.2 V 50% to 100% load step at Vin=12 V, Vo=1.8 V Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 0.75 Vdc - 5.5 Vdc/6 A Output 100% to 50% load step at Vin=12 V, Vo=0.75 V 100% to 50% load step at Vin=12 V, Vo=1 ...
Page 9
... Note: Transient response is tested at di/dt=2.5 A/uS, with 10 uF/10 V tantalum capacitor and 1 uF/10 V ceramic capacitor, Ta=25 deg C. Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com 0.75 Vdc - 5.5 Vdc/6 A Output 100% to 50% load step at Vin=12 V, Vo=2.5 V 100% to 50% load step at Vin=12 V, Vo=3 ...
Page 10
... Function 1 Remote On/Off 2 Vin+ 3 SEQ 4 Ground 5 Trim 6 Vout+ © 2007 Bel Fuse Inc. Specifications subject to change without notice. 011207 EUROPE Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com ...