DPP15-24 TDK Corporation, DPP15-24 Datasheet - Page 2

• Manufacturer Part Number: DPP15-24
• Description: PWR SUP DIN RAIL 24V 15W .63A
• Manufacturer: TDK Corporation
• Series: DPPr
• Type: Commercialr

Specifications of DPP15-24

• Power Supply Type: Switching (Closed Frame)
• Voltage - Output: 24V
• Number Of Outputs: 1
• Power (watts): 15W
• Applications: Commercial
• Voltage - Input: 85 ~ 264VAC
• Mounting Type: DIN Rail
• 1st Output: 24 VDC @ 630mA
• Size / Dimension: 3.81" L x 0.9" W x 2.95" H (96.8mm x 22.9mm x 74.9mm)
• Power (watts) - Rated: 15W
• Operating Temperature: -10°C ~ 71°C
• Efficiency: 81%
• Approvals: CE, EN, UL
• Line Regulation: 0.5%
• Load Regulation: 0.5%
• Power Supply Output Type: Fixed
• No. Of Outputs: 1
• Output Voltage: 24V
• Output Current: 0.63A
• Power Rating: 15W
• Input Voltage: 85V AC To 264V AC / 90V DC To 375V DC
• Brand/series: DPP Series
• Configuration: Enclosed
• Current, Inrush: 35 A (Min.)
• Current, Rating: 0.63 A
• Frequency: 47 to 63 Hz
• Height: 2.95 in.
• Operation: Switching
• Output: 24 VDC @ 0.63 A
• Power, Output: 15 W
• Primary Type: AC-DC
• Temperature, Operating, Maximum: 71 °C
• Temperature, Operating, Minimum: -10 °C
• Voltage, Input: 85 to 264/90 to 375 VAC/VDC
• Voltage, Output: 24 VDC
• Voltage, Rating: 24 V
• Width: 0.9 in.
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: 285-1213; DPP1524

Read Instructions!
Disconnect system from supply network
Before start of operation
Ensure appropriate installation
In operation: No modifications!
Convection cooling (See Fig.1)
Warning: High voltage! Stored energy!
Only connect/disconnect when the power is off!
Before working with this unit, read these instructions
carefully and completely. Make sure that you have
understood all the information!
Before any installation, maintenance or modification work:
Disconnect your system from the supply network. Ensure that it
cannot be re-connected inadvertently!
Warning! Improper installation / operation impair safety and result in
operational difficulties or complete failure of the unit.
The DPP family of component power supplies is designed for use
within other equipment or enclosures which restrict access to
authorised competent personnel only. The unit covers/chassis are
designed to protect only skilled personnel from hazards and must not
be made user accessible.
The unit must be installed and put into service appropriately by
qualified personnel. Compliance with the relevant regulations must
be ensured. Before operation is begun the following conditions must
be ensured, in particular:
As long as the unit is in operation: do not modify the
installation! The same applies also to the secondary side. Risk
of electric arcs and electric shock (fatal)!
Do not cover any ventilation holes!
Leave sufficient space around the unit for cooling!
The unit contains unprotected conductors carrying a lethal
high voltage, and components storing substantial amounts of
energy. Improper handling may result in an electric shock or
serious burn!
The unit must not be opened except by appropriately trained
personnel!
Do not introduce any object into the unit!
Keep away from fire and water!
Connection to main power supply in compliance with VDE0100 and
With stranded wires: all strands must be secured in the terminal
Unit and power supply cables must be properly fused; if necessary
The non-fused earth conductor must be connected to the "
All output lines must be rated for the power supply output current
Sufficient air-cooling must be ensured.
EN50178.
blocks (potential danger of short circuit).
a manually controlled disconnecting element must be used to
disengage from supply mains.
terminal (protection class 1).
and must be connected with the correct polarity.
Safety notes
"
Installation
Mounting
Snap on support rail
Technical Data
Input
Output
General
Permissible mounting position: keep ventilation holes clear,
leave space for cooling! Recommended to have 25mm
free space at all sides:
Rated input Voltage
AC Voltage Range
DC Voltage Range
Frequency
Rated input Current
Inrush Current(115Vac/230Vac)
Efficiency Typ.
Power Factor Correction
Fuse Rating (Internal)
Turn on time
Voltage Rise Time
Overvoltage protection
Voltage trim range
Line regulation
Load regulation
Time & temp. Drift
Initial voltage setting
DC ON indicate(Green LED)
Ripple
Nominal Current
Rated over load protection
Current Limit
Holdup Time(115Vac/230Vac)
Voltage fall Time
Parallel Operation
Temperature
Humidity
MTBF(MIL-HDBK-217F.GF25)
Case
Dimensions
H x W x D(inches / mm)
Weight
IP rating
Emissions
Immunity
Approvals
Tilt the unit slightly rearwards.
Fit the unit over top hat rail.
Slide it downward until it hits the stop.
Press against the bottom front side for locking.
Shake the unit slightly to check the locking action.
Description
(See Fig. 1)
All specifications are typical at nominal line, full load,25 ; Unless otherwise specified.
(See Fig. 2)
>30 but <33Vdc
(75 x 22.8 x 96.7)
22.5-28.5 Vdc
2.95 x 0.9 x 3.81
EN61000-6-3,EN55011,EN55022 Class B Radiated and Conducted including Annex. A.
EN61000-6-2,EN61000-4-2 Level 4,EN61000-4-3 Level 3,EN61000-4-6 Level 3,
EN61000-4-4 Level 4 input and level 3 output. EN61000-4-5 level 4,EN61000-4-8,EN61000-4-11
EN60950-1,UL508 Listed, UL 60950-1, NEC Class 2 except DPP100-24, CE marked for EMC(2004/108/EC)
110%~150%
DPP15-24
24.5V 1%
287,000 hrs
0.4/0.25A
Typ.<35A
T1AH,250V
80%
>18V
0.6A
130g
Fold Forward (Current rises, voltage drops to maintain constant power during overload p to max peak curr e nt)
120%~135%
DPP25-5
294,000 hrs
<6.7Vdc
0.6/0.4A
5-6 Vdc
5V 1%
78%
>4V
5A
Storage:-25 to +85
Typ.<35A / Typ.<45A
9.9-12.1 Vdc
135%~160%
DPP30-12
288,000 hrs
<18Vdc
Switch selectable Via front panel------DPP 100-24 model only
12V 1%
0.7/0.4A
>7.92V
82%
2.5A
<1000mS after AC is applied to input at full resisti ve load
<150mS from 95% to 10% rate d voltage @ full load
o
C
, Operation-10 to+ 60
115Vac / 230Vac
>30 but <33Vdc
22.5-28.5 Vdc
120%~150%
DPP30-24
Connection
85 - 264Vac
24.5V 1%
304,000 hrs
Removal
90-375Vdc
<150mS full resistive load
50 / 60Hz
0.7/0.4A
Use only commercial cables designed for the indicated
voltage and current values!
With flexible cables: make sure that all stranded cable are
secured in the terminal.
Ensure proper polarity at output terminals!
84%
>18V
1.3A
Push the slider downwards (unlock). Gently lift
lower front edge of the unit (tipping) and remove.
o
meet EN61000-3-2 class A
C
2.95 x 1.77 x 3.58
>20ms / >25ms
20%~90%RH
(75 x 45 x 91)
Model No.
<50m Vp-p
<0.5%
<0.5%
<1.0%
Plastic
260g
IP 20
T2AH/250V
o
from DIN Rail (See Fig. 4)
11.9-15.1 Vdc
C
135%~155%
DPP50-15
269,000 hrs
15V 1%
derating to half power from 60 to 70
>9.52V
<20Vdc
(See Fig. 3)
1.1/0.7A
85%
3.4A
Typ.<35A / Typ.<50A
>30 but <33Vdc
22.5-28.5 Vdc
120%~150%
DPP50-24
24.5V 1%
273,000 hrs
1.1/0.7A
>18V
86%
2.1A
125%~145%
DPP50-48
283,000 hrs
48-56 Vdc
48V 1%
1.1/0.7A
<66Vdc
>38.4V
o
C
87%
1.0A
115/230 Vac auto select
85-132 / 176-264
Typ.<35A / Typ.<55A
>30 but <33Vdc
42.95 x 2.85 x 3.81
22.5-28.5 Vdc
(75 x 72.5 x 96.7)
DPP100-24
T3.15AH/250V
115%~140%
210-375 Vdc
24.5V 1%
239,000 hrs
2.2/1.2A
>18V
87%
4.2A
390g
DM088-A2