70-841-016 Emerson Network Power, 70-841-016 Datasheet

no-image

70-841-016

Manufacturer Part Number
70-841-016
Description
KIT CONNECTOR MATING LPS170
Manufacturer
Emerson Network Power
Series
LPS170r
Datasheet

Specifications of 70-841-016

Accessory Type
Connector Kit
For Use With/related Products
LPS170
Lead Free Status / Rohs Status
No
118
175 Watts
LPS170 Series
• Active power factor correction
• IEC EN61000-3-2 compliance
• Wide Range Adjustable output
• Single wire current sharing
• Power fail and remote inhibit
• Built-in EMI filter
• Low output ripple
• Overvoltage protection
• Overload protection
• Thermal overload protection
• DC power good
• 5 V standby output
• 12 V Aux output
• Optional cover (-C suffix)
Operating temperature: 0° to 50°C ambientderate
each output at 2.5% per degree from 50° to 70°C
Electromagnetic susceptibility: designed to meet
IEC EN61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3
Humidity: Operating; non-condensing
5% to 95%
Vibration: Three orthogonal axes, sweep at
1 oct/min, 5 min. dwell at four major resonances
0.75 G peak 5 Hz to 500 Hz, operational
Storage temperature: -40° to 85°C
Temperature coefficient: ± .04% per °C
MTBF demonstrated: >550,000 hours at full load
and 25°C ambient conditions
America’s (USA): 1-888-41-ASTEC
Remote sense on main output
Special Features
Environmental
Europe (UK): 44 (1384) 842-211
Total Power:
Input Voltage: 85-264 VAC
# of Outputs:
Input
Input range
Frequency
Inrush current
Efficiency
EMI filter
Power factor
Safety ground
leakage current
Output
Maximum power
Adjustment range
Hold-up time
Overload protection
Overvoltage protection
Standby output
Aux output
Logic Control
Power failure
Remote inhibit
Remote sense
DC Ok
VDE
UL
CB
CSA
CE
NEMKO
110-175 Watts
120-300 VDC
Single
Electrical Specs
0805/EN60950 (IEC950)
UL1950
Certificate and report
CSA 22.2-234 Level 3
Mark (LVD)
EN 60950/EMKO-TUE
Asia (HK): 852-2437-9662
Safety
85-264 VAC, 120-300 VDC
47-63 Hz
38 A max, cold start @ 25°C
75% typical at full load
Meets FCC Class B conducted
CISPR 22 Class B conducted
EN55022 Class B conducted
VDE 0878 PT3 Class B conducted
0.99 typical
1.0 mA @ 50/60 Hz, 264 VAC input
110 W convection (75 W with cover)
175 W with 30 CFM forced air
(130 W with cover)
2:1 wide ratio minimum
20 ms @175 W load at nominal line
Short circuit protection on all outputs.
Case overload protected @ 110-145%
above peak rating
10% to 40% above nominal output
5 V @ 2A regulated ±5%
12 V @ 1 A -5 %, +10%
TTL logic signal goes high 100 - 500
msec after V1 output; It goes low at
least 4 msec before loss of regulation
Requires contact closure to inhibit
outputs
Compensates for 0.5 V lead drop min.
Will operate without remote sense
connected. Reverse connection
protected.
TTL logic signal goes high after main
output is in regulation. It goes low
when there is a loss of regulation
rev 01.14.03

Related parts for 70-841-016

70-841-016 Summary of contents

Page 1

... V standby output • Aux output • Optional cover (-C suffix) Environmental Operating temperature: 0° to 50°C ambientderate each output at 2.5% per degree from 50° to 70°C Electromagnetic susceptibility: designed to meet IEC EN61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3 Humidity: Operating; non-condensing 5% to 95% Vibration: Three orthogonal axes, sweep at 1 oct/min, 5 min ...

Page 2

... Molex 19141-0058 (SK1) Control Signals: Molex 90142-0010 (USA) PINS: 90119-2110 or Amp: 87977-3 PINS: 87309-8 Astec connector kit #70-841-016 Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is ±0.02”. 3. Specifications are for convection rating at factory settings unless otherwise stated. 4. Mounting screw maximum insertion depth is 0.12”. ...

Related keywords