7023-D-N-1000 LEDdynamics Inc, 7023-D-N-1000 Datasheet
7023-D-N-1000
Specifications of 7023-D-N-1000
Related parts for 7023-D-N-1000
7023-D-N-1000 Summary of contents
Page 1
... Product Overview The 7021 and 7023 BuckPlus LED Power Modules are a line of true current regulated drivers for powering LEDs. The BuckPlus line of LED drivers are the ideal choice for powering all types of high- brightness and high-power LED Packages and LED arrays. ...
Page 2
... LUXdrive, A Division of LEDdynamics, Inc. www.LUXdrive.com. Specifications subject to change without notice. April, 2010 - Rev 2.2 Connection Type 7-Pin SIP (4 Pins) 7-Pin SIP (6 Pins) 7-Pin SIP (6 Pins) 4 Wires 6 Wires LED + LED - Ctrl 7021 Ref 7023 Vin+ Vin - Figure 1. Bottom view Pinout of the 7021/7023 BuckPlus Figure 3. TM ...
Page 3
... Specifications Output current, 7021-x-x-350, 7023-x-x-350 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350mA Output current, 7021-x-x-500, 7023-x-x-500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mA Output current, 7021-x-x-700, 7023-x-x-700 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700mA Output current, 7021-x-x-1000, 7023-x-x-1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000mA Control Pin, adjustment threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.65 V ±5% Control Pin, shutoff threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 V ±5% Control Pin, propagation delay to output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <15 μs Control Pin, input impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5k ohm Reference voltage ( greater) ...
Page 4
... Figures 14 and 15 show two methods for low speed pulsing or high speed flashing operation. In Figure 14 TTL/CMOS logic signal is applied directly to the control (Ctrl) input of the 7021/7023. The output current will be zero when the control signal is high. Note that the input needs to source a minimum of 4.75V input impedance ...
Page 5
... Connections In all cases, the LEDs being driven should be located as close to the 7021/7023 LED output as possible. When the use of long leads is required, use heavier gauge wire. For strobe or pulse applications, a wire length not exceeding 6" should be used to maintain accurate timing. ...
Page 6
... External potentiometer using internal LEDdynamics, Inc. reference 802.728.4533 P 802.728.3800 F sales@LUXdrive.com * - Luxeon is a registered trademark of LumiLEDs Corporation www.LUXdrive.com 7021/7023 BuckPlus 1000mA unit driving three High Power LEDs LED+ LED- 700mA unit driving three High Power LEDs LED+ LED- External potentiometer using external voltage © ...
Page 7
... GND Other I/O Lines Figure 16. Interface to PIC or other microcontroller Figure 15. Interface to PIC or other microcontroller LEDdynamics, Inc. 802.728.4533 P 802.728.3800 F sales@LUXdrive.com www.LUXdrive.com 7021/7023 BuckPlus LED+ LED OFF External dimming plus ON/OFF control with LED+ LED OFF LED+ LED- Using resistor for fixed current reduction ...
Page 8
... Place a capacitor across the input terminals when the distance to the DC Physical Dimensions 20.96 mm [0.83”] 19.80 mm [0.78”] 7021 LEDdynamics, Inc. 802.728.4533 P 802.728.3800 F sales@LUXdrive.com www.LUXdrive.com 7021/7023 BuckPlus LED+ 7021/7023 V in LED- CTRL REF Figure 18. power source is greater than 18 inches 11.0 mm [0.43”] 5.84 mm [0.23” ...