28128 Parallax Inc, 28128 Datasheet - Page 105
28128
Manufacturer Part Number
28128
Description
KIT BASIC ANALOG/DIGI PARTS ONLY
Manufacturer
Parallax Inc
Datasheet
1.28129.pdf
(176 pages)
Specifications of 28128
Accessory Type
ADC, DAC
Product
Microcontroller Accessories
For Use With/related Products
BASIC Stamp® 2 and Board of Education
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 105 of 176
- Download datasheet (3Mb)
peak amplitude. The D/A converter's output is programmed for a maximum of 3 volts and
a minimum of 1.6 volts. Therefore the peak-to-peak amplitude is 3 – 1.6 volts = 1.4 volts.
The DC offset is the difference between 0 volts and the waveform's minimum value. We
already know the lowest point of the sample triangle wave is 1.6 volts, and that's the DC
offset.
An alternative reference point for both Amplitude and DC offset is half way between the
upper and lower peak. The half way point would be (3 + 1.6), 2 volts = 2.3 volts. The
amplitude would be 3 – 2.3 volts = 0.7 volts. The DC offset would be 1.6 + 0.7 volts =
2.4 volts.
The
block. This code block uses a
counts for
D/A converter increases and then decreases in the Stamp-O-Scope display.
Each time a
sends the program to the
The
difference is that now it's a subroutine. The
our Stamp-O-Scope display, so the
save EEPROM memory, you could also delete the entire subroutine. Keep that in mind if
you use this in a larger application and start to run out of EEPROM memory to store your
program.
About the Code
Main
Main
DO
LOOP
Main:
subroutine still does the same job it did in the previous experiment. The only
n
routine is has been relegated to a subroutine in favor of the
FOR n = 7 TO 15
NEXT
FOR n = 14 TO 8
NEXT
GOSUB DAC
GOSUB ADC_Data
'GOSUB Calc_Volts
, the value sent to the D/A converter. This is why the measured output of the
FOR…NEXT
GOSUB Main
GOSUB Main
loop in the
Main
subroutine.
FOR…NEXT
DO…LOOP
GOSUB Calc_Volts
loop to increment and decrement up and down
Calc_Volts
routine increments the value of
subroutine is not necessary for
command is commented. To
DO…LOOP
n
, it also
code
Related parts for 28128
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Microcontroller Modules & Accessories DISCONTINUED BY PARALLAX
Manufacturer:
Parallax Inc
Part Number:
Description:
BOOK UNDERSTANDING SIGNALS
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
COMPETITION RING FOR SUMOBOT
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
TEXT INFRARED REMOTE FOR BOE-BOT
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
BOARD EXPERIMENT+LCD NX-1000
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
CONTROLLER 16SERVO MOTOR CONTROL
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
BASIC STAMP LOGIC ANALYZER
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
IC MCU 2K FLASH 50MHZ SO-18
Manufacturer:
Parallax Inc
Datasheet: