28176 Parallax Inc, 28176 Datasheet - Page 213
28176
Manufacturer Part Number
28176
Description
KIT PARTS PROCESS CONTROL W/TEXT
Manufacturer
Parallax Inc
Datasheet
1.122-28176.pdf
(330 pages)
Specifications of 28176
Accessory Type
Process Control
Product
Microcontroller Accessories
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
For Use With/related Products
BASIC Stamp® 2 and Board of Education
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Contains lead / RoHS non-compliant
- Current page: 213 of 330
- Download datasheet (11Mb)
The resistor is 100 Ω ½ watt. The "power rating", ½ watt, means how much heat it can
dissipate before becoming hot enough to damage it with long-term continuous use. With
a 9 V supply, the resistor will be dissipating more heat than it is rated for:
This is almost twice the rated power of the device. As such, the resistor will get very hot
and may discolor with prolonged use.
Additional Parts Required
(1) 2N3904 Transistor - BJT
(1) BS170 Transistor – FET
(1) 220 Ω Resistor
(2) 1 kΩ Resistors
(1) LED
(1) 100 Ω ½ W Resistor (Heater)
(1) 12 V Fan
(1) Polystyrene Test Tube
(1) 9 V battery (not included)
√
√
√
√
√
P = V
If you are using a wall-mount power supply, disconnect it from your board
Construct the circuit in Figure 6-17. The heating resistor (100 Ω ½ watt, R3)
needs to have one lead tightly bent in a U-turn so it can stand vertically up from
the board.
Place the plastic test tube on the breadboard directly over R
Place the fan approximately 3 inches from the incubator so the fan will blow
towards the incubator, as shown in Figure 6-19. (The fan is facing the opposite
direction than it was in previous chapters.)
Connect the 9 V battery to your board.
WARNING: Do not use an unregulated 9 V wall-mount power supply for this activity.
Use a fresh 9 V battery (this activity will drain the battery). The resistor will reach
temperatures high enough to melt soft plastic.
incubator circuit. Do not allow the test tube to touch the resistor directly; even so, it
may warp. NEVER LEAVE POWERED CIRCUITS UNATTENDED!
2
/R = (9V)
2
/100 Ω = 0.81 W.
Use care when constructing the
3
and the LM34.
Related parts for 28176
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Microcontroller Modules & Accessories DISCONTINUED BY PARALLAX
Manufacturer:
Parallax Inc
Part Number:
Description:
BOOK UNDERSTANDING SIGNALS
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
COMPETITION RING FOR SUMOBOT
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
TEXT INFRARED REMOTE FOR BOE-BOT
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
BOARD EXPERIMENT+LCD NX-1000
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
CONTROLLER 16SERVO MOTOR CONTROL
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
BASIC STAMP LOGIC ANALYZER
Manufacturer:
Parallax Inc
Datasheet:
Part Number:
Description:
IC MCU 2K FLASH 50MHZ SO-18
Manufacturer:
Parallax Inc
Datasheet: