ATSTK600-DIP40 Atmel, ATSTK600-DIP40 Datasheet - Page 8

STK600 SOCKET/ADAPTER 40-PDIP

ATSTK600-DIP40

Manufacturer Part Number
ATSTK600-DIP40
Description
STK600 SOCKET/ADAPTER 40-PDIP
Manufacturer
Atmel
Series
AVR®r
Datasheet

Specifications of ATSTK600-DIP40

Module/board Type
Socket Module - DIP
Processor To Be Evaluated
ATSTK600
Data Bus Width
8 bit
Convert From
40-DIP
Convert To
STK600
Supported Devices
ATSTK600 Dev Kit
Mcu Supported Families
AVR/AVR32 Microcontroller
Rohs Compliant
Yes
For Use With/related Products
STK600
For Use With
ATSTK600 - DEV KIT FOR AVR/AVR32
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATSTK600-DIP40
Manufacturer:
Atmel
Quantity:
135
3 Socket cards
3.1 Power design issues
3.2 Connector MPN
8
AVR600
Socket cards route each pin from the IC socket to separate pins on the spring loaded
connectors on the bottom side, facing the routing card.
Since all routing is handled by the routing card, even power lines and power
decoupling is ignored at the socket card. This produces less than ideal power design
which may lead to unwanted noise, ground bounce and other effects. It should
therefore be expected that heavily loaded designs can not run at full speed on
STK600. Likewise, such power design is not recommended for custom designs.
Table 3-1. Socket card connector
STK600 Signal name
TGT_SCK, TGT_MISO,
TGT_MOSI
TGT_TDI, TGT_TDO,
TGT_TMS, TGT_TCK
VBUST
UID
UVCON
DP, DN
TGT_PDATA(0-7)
TGT_CTRL0
TGT_CTRL1
TGT_CTRL2
TGT_CTRL3
TGT_CTRL4
TGT_CTRL5
TGT_CTRL6
TGT_CTRL7
BOARD_IDn
Notes:
Manufacturer and MPN
SAMTEC, FSI-140-03-G-D-AD
1. Not all AVR will have every pin (ex. two aref pins, tosc or usb)
2. A MCU pin will fan-out to both Pnx pin and to the programming interface(s)
located at that pin.
MCU
ISP pins
JTAG pins
VBUS
UID
UVCON
DP, DN
(HV) data pins
(HV) BS2
(HV) Ready/Busy
(HV) /OE
(HV) /WR
(HV) BS1
(HV) XA0
(HV) XA1
(HV) PAGEL
none
Quantity
2
Comment
ISP programming interface
JTAG programming interface
VBUS (sense) for USB
ID pin for USB OTG
USB VBUS generation control for
USB OTG. A low level on this
signal enables VBUS generation.
USB differential pair
Data pins for high voltage
(PP/HVSP) programming.
Control signals for High voltage
Parallell Programming / Serial
Programming. Please refer to
AVR datasheet for further
information.
On AVRs with common
XA1/BS2, XA1 is used.
On AVRs with common
BS1/PAGEL, BS1 is used.
ID system for router / socket /
expansion cards, see section 5 -
ID System
Comment
Spring loaded 80-pin connector
8170B-AVR-12/10