AC162049 Microchip Technology, AC162049 Datasheet
AC162049
Manufacturer Part Number
AC162049
Description
MODULE SOCKET FOR ICD2 DIP
Manufacturer
Microchip Technology
Specifications of AC162049
Module/board Type
Socket Module - DIP
Positions/sockets
1
Accessory Type
Programing Module
Features
ZIF DIP-40 Socket
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
ICD2
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With
ICD2
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AC162049
Manufacturer:
Microchip Technology
Quantity:
135
Universal Programming Module
AC162049 Instruction Sheet
____________________________________________________________________
The Universal Programming Module (UPM) is a handy, low-cost tool to support programming of
FLASH-based microcontroller DIP packaged products from Microchip Technology using the
MPLAB ICD 2 In-Circuit Debugger. It can also be connected to the PICSTART Plus, allowing
programming of parts previously unsupported due to pin configuration issues.
Configuration of the Jumpers:
connected to the two 20-pin headers marked 1 through 40. These connect the power supply and needed
programming lines. The configuration will vary based on the microcontroller device being
programmed. For the proper jumper configuration for the microcontroller being used, please see the
Readme files for MPLAB ICD 2 and PICSTART Plus, found in the MPLAB IDE installation
directory.
Loading/Programming Device:
devices. Be sure power is removed prior to inserting the device into the ZIF socket. Also, the handle
for the ZIF socket should be in the down position. The device should drop in with zero force. Insert
the device so that the top is aligned with the top of the ZIF socket (i.e., pin 1 to pin 1). Once inserted,
raise the handle on the socket 90 degrees to the full locked position.
LED 1 -
Removing a Programmed Part:
complete, remove power from the board and lower the arm (unlock) on the ZIF socket. The device
should lift out without any resistance.
PICSTART Plus Use:
#TSW-120 series or equivalent and install (solder into place) two headers on the bottom of the UPM in
the holes provided. Once installed, the UPM can be inserted into the 40-pin DIP socket on the
programmer. The jumpers must then be configured per the instruction found in the Readme file for
PICSTART Plus.
Microchip Technology Inc., 2355 W. Chandler Blvd., Chandler, AZ 85224
PROGRAMMING THE MICROCONTROLLER OR IT WILL NOT PROGRAM PROPERLY.
ZIF SOCKET HANDLE MUST BE IN THE UP (LOCKED) POSITION PRIOR TO
AN EXTERNAL 9V DC POWER SUPPLY (AC162039) MUST BE CONNECTED
Led 1 will illuminate whenever programming activity occurs on the board.
TO THE MPLAB ICD 2 WHEN PROGRAMMING WITH THE UPM.
In order to use the UPM on this programmer, you must purchase Samtec
*****WARNING *****
*****WARNING *****
There are seven jumpers (flying leads located at J3) that must be
The ZIF socket will support 18-, 28- and 40-pin DIP packaged
After MPLAB IDE acknowledges that programming is
(480) 792-7200
DS51280A
Related parts for AC162049
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet: