Z8F64210100ZDV Zilog, Z8F64210100ZDV Datasheet - Page 213
![ADAPTER ICE Z8 ENCORE 64K 44PLCC](/photos/9/2/90270/z8f64210100zdv_sml.jpg)
Z8F64210100ZDV
Manufacturer Part Number
Z8F64210100ZDV
Description
ADAPTER ICE Z8 ENCORE 64K 44PLCC
Manufacturer
Zilog
Specifications of Z8F64210100ZDV
Module/board Type
*
For Use With/related Products
Z8 Encore!™
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
269-3402
- Current page: 213 of 297
- Download datasheet (9Mb)
®
Z8 Encore! XP
F64XX Series
Product Specification
199
The host transmits a Serial Break on the DBG pin when first connecting to the Z8 Encore!
®
XP
F64XX Series devices or when recovering from an error. A Serial Break from the
host resets the Auto-Baud Generator/Detector but does not reset the OCD Control register.
A Serial Break leaves the device in DEBUG mode if that is the current mode. The OCD is
held in Reset until the end of the Serial Break when the DBG pin returns High. Because of
the open-drain nature of the DBG pin, the host can send a Serial Break to the OCD even if
the OCD is transmitting a character.
Breakpoints
Execution Breakpoints are generated using the BRK instruction (opcode 00H). When the
eZ8 CPU decodes a BRK instruction, it signals the On-Chip Debugger. If Breakpoints are
enabled, the OCD idles the eZ8 CPU and enters DEBUG mode. If Breakpoints are not
enabled, the OCD ignores the BRK signal and the BRK instruction operates as an NOP.
If breakpoints are enabled, the OCD can be configured to automatically enter DEBUG
mode, or to loop on the break instruction. If the OCD is configured to loop on the BRK
instruction, then the CPU is still enabled to service DMA and interrupt requests.
The loop on BRK instruction can be used to service interrupts in the background. For
interrupts to be serviced in the background, there cannot be any breakpoints in the inter-
rupt service routine. Otherwise, the CPU stops on the breakpoint in the interrupt routine.
For interrupts to be serviced in the background, interrupts must also be enabled. Debug-
ging software should not automatically enable interrupts when using this feature, since
interrupts are typically disabled during critical sections of code where interrupts should
not occur (such as adjusting the stack pointer or modifying shared data).
Software can poll the IDLE bit of the OCDSTAT register to determine if the OCD is loop-
ing on a BRK instruction. When software wants to stop the CPU on the BRK instruction it
is looping on, software should not set the DBGMODE bit of the OCDCTL register. The
CPU may have vectored to and be in the middle of an interrupt service routine when this
bit gets set. Instead, software must clear the BRKLP bit. This action allows the CPU to
finish the interrupt service routine it may be in and return the BRK instruction. When the
CPU returns to the BRK instruction it was previously looping on, it automatically sets the
DBGMODE bit and enter DEBUG mode.
Software detects that the majority of the OCD commands are still disabled when the
eZ8
TM
CPU is looping on a BRK instruction. The eZ8 CPU must be stopped and the part
must be in DEBUG mode before these commands can be issued.
Breakpoints in Flash Memory
The BRK instruction is opcode
, which corresponds to the fully programmed state of a
00H
byte in Flash memory. To implement a Breakpoint, write
to the desired address, over-
00H
writing the current instruction. To remove a Breakpoint, the corresponding page of Flash
memory must be erased and reprogrammed with the original data.
PS019921-0308
On-Chip Debugger
Related parts for Z8F64210100ZDV
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![Z8018218FSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
Communication Controllers, ZILOG INTELLIGENT PERIPHERAL CONTROLLER (ZIP)
Manufacturer:
Zilog, Inc.
Datasheet:
![Z8F64200100KITG](/photos/9/20/92054/z8f64200100kitg_tmb.jpg)
Part Number:
Description:
KIT DEV FOR Z8 ENCORE 16K TO 64K
Manufacturer:
Zilog
Datasheet:
![Z8F08A28100KITG](/photos/9/22/92241/z8f08a28100kitg_tmb.jpg)
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
![Z8F08200100KITG](/photos/9/22/92242/z8f08200100kitg_tmb.jpg)
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 8K/4K
Manufacturer:
Zilog
Datasheet:
![Z8F04A28100KITG](/photos/9/22/92243/z8f04a28100kitg_tmb.jpg)
Part Number:
Description:
KIT DEV Z8 ENCORE XP 28-PIN
Manufacturer:
Zilog
Datasheet:
![Z8F08200100KIT](/images/manufacturer_photos/0/7/729/zilog_tmb.jpg)
Part Number:
Description:
DEV KIT FOR Z8 ENCORE 4K TO 8K
Manufacturer:
Zilog
Datasheet:
![Z86C6116FSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
CMOS Z8 microcontroller. ROM 16 Kbytes, RAM 256 bytes, speed 16 MHz, 32 lines I/O, 3.0V to 5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86E0208PSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
Low-cost microcontroller. 512 bytes ROM, 61 bytes RAM, 8 MHz
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86E40](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
Z8 4K OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
![Z88C0020VEC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
CMOS SUPER8 ROMLESS MCU
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86E0812SSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86E0812PSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
SL1866 CMOSZ8 OTP Microcontroller
Manufacturer:
Zilog, Inc.
Datasheet:
![Z86E0412PSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
OTP (KB) = 1, RAM = 125, Speed = 12, I/O = 14, 8-bit Timers = 2, Comm Interfaces Other Features = Por, LV Protect, Voltage = 4.5-5.5V
Manufacturer:
Zilog, Inc.
Datasheet:
![Z9023306PSC](/images/manufacturer_photos/0/7/730/zilog__inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Zilog, Inc.
Datasheet: