MCP2140DM-TMPSNS Microchip Technology, MCP2140DM-TMPSNS Datasheet - Page 47

• Manufacturer Part Number: MCP2140DM-TMPSNS
• Description: BOARD DEMO FOR MCP2140
• Manufacturer: Microchip Technology

Specifications of MCP2140DM-TMPSNS

• Main Purpose: Interface, IrDA
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: MCP2140
• Primary Attributes: IrDA Controller with PIC18F MCU and Temp Sensor Temp
• Secondary Attributes: Set up as a Data Logger
• Processor To Be Evaluated: MCP2140
• Interface Type: ICSP
• Silicon Manufacturer: Microchip
• Silicon Core Number: MCP2140
• Kit Application Type: Sensing - Temperature
• Application Sub Type: Temperature Sensor
• Kit Contents: Board
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: MCP2140DM-TMPSNSR; MCP2140DM-TMPSNSR

B.1.2
The IrLAP protocol provides:
• Management of communication processes on the
• A device-to-device connection for the reliable,
• Device discover procedures
• Hidden node handling. 115.2 kbaud
Figure B-3
IrDA protocols. The bottom layer is the Physical layer,
IrPHY. This is the part that converts the serial data to
and from pulses of IR light. IR transceivers can’t trans-
mit and receive at the same time. The receiver has to
wait for the transmitter to finish sending. This is some-
times referred to as a “Half-Duplex” connection. The IR
Link Access Protocol (IrLAP) provides the structure for
packets (or “frames”) of data to emulate data that would
normally be free to stream back and forth.
FIGURE B-3:
2003 Microchip Technology Inc.
link between devices
ordered transfer of data
Note:
Host O.S. or Application
identifies the key parts and hierarchy of the
Not supported by MCP2140.
IrLAP
IrLMP – IAS
IrCOMM
IrPHY
IrDA STANDARD PROTOCOL
LAYERS
IrLAP
IR pulses
transmitted
and
received
Protocols
resident in
MCP2140
Preliminary
Figure B-4
The frame is preceded by some number of Beginning
of Frame characters (BOFs). The value of the BOF is
generally 0xC0, but 0xFF may be used if the last BOF
character is a 0xC0. The purpose of multiple BOFs is to
give the other station some warning that a frame is
coming.
The IrLAP frame begins with an address byte (“A”
field), then a control byte (“C” field). The control byte is
used to differentiate between different types of frames
and is also used to count frames. Frames can carry sta-
tus, data or commands. The IrLAP protocol has a com-
mand syntax of it’s own. These commands are part of
the control byte. Lastly, IrLAP frames carry data. This
data is the information (or “I”) field. The integrity of the
frame is ensured with a 16-bit CRC, referred to as the
Frame Check Sequence (FCS). The 16-bit CRC value
is transmitted LSB first. The end of the frame is marked
with an EOF character, which is always a 0xC1. The
frame structure described here is used for all versions
of IrDA protocols used for serial wire replacement for
speeds up to 115.2 kbaud.
FIGURE B-4:
In addition to defining the frame structure, IrLAP pro-
vides the “housekeeping” functions of opening, closing
and maintaining connections. The critical parameters
that determine the performance of the link are part of
this function. These parameters control how many
BOFs are used, identify the speed of the link, how fast
either party may change from receiving to transmitting,
etc. IrLAP has the responsibility of negotiating these
parameters to the highest common set so that both
sides can communicate as quickly and reliably as
possible.
Note 1: The
X BOFs BOF A C
(1+N) of C0h payload
2: Another IrDA standard that is entering
3: IrDA communication standards faster
shows how the IrLAP frame is organized.
communication baud rate of 9600 baud.
into general usage is IR Object Exchange
(IrOBEX). This standard is not used for
serial connection emulation.
than 115.2 kbaud use a different CRC
method and physical layer.
IrLAP FRAME
MCP2140
MCP2140
I
bytes C1h
FCS
2
only
DS21790A-page 47
EOF
supports