IS-DEV KIT-5 NKK Switches, IS-DEV KIT-5 Datasheet - Page 12
![SMARTSWITCH DEVELOPMENT KIT 5](/photos/9/5/90525/mfg_is-dev_kit-5_sml.jpg)
IS-DEV KIT-5
Manufacturer Part Number
IS-DEV KIT-5
Description
SMARTSWITCH DEVELOPMENT KIT 5
Manufacturer
NKK Switches
Series
SmartSwitch™r
Datasheet
1.IS-L0251-C.pdf
(24 pages)
Specifications of IS-DEV KIT-5
Main Purpose
Switches with Programmable Display
Utilized Ic / Part
IS15ABFP4RGB
Primary Attributes
2 LCD Switches, PC Board with Flash Memory
Secondary Attributes
Power and Programming Connections
Description/function
SMARTSWITCH Development Kit
For Use With
360-2431 - SERIAL CBL RJ11-DB9 FOR DEV KIT360-2430 - POWER SUPPLY 240VAC FOR DEV KIT360-2429 - POWER SUPPLY 120VAC FOR DEV KIT
Lead Free Status / RoHS Status
Not applicable / Not applicable
Embedded
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
For Use With/related Products
Smart Switch - RGB
Other names
360-2328
7850 East Gelding Drive • Scottsdale, AZ 85260-3420
Command to set one LCD/LED Code
[LCD Module #] is the switch number (31H for switch 1, 32H for switch 2)
[LED code] is one byte for LCD 36x24 and two bytes for LCD 64x32 (first byte for on-cycle and second byte
for off cycle). B0 and B1 must be 1 for LCD 64x32.
Command to query controller for mode, controller, and firmware version
[mode] is one byte. 31H indicates LCD 36x24 module mode or 32H indicates LCD 64x32 mode.
[Controller name] is five bytes. 43H 30H 32H 30H 33H (C0203)
[version] is one byte. 12H (version 1.1)
Command to upload the active Addresses
Command to set the data version
Command to upload the data version
IS-Dev Kit-5 and IS-Dev Kit-6 Users Manual A.doc
This command updates the LED’s of specified switch with the LED code.
This command queries the controller for the mode as set by the Mode Select Switch, the controller
name, and the firmware version installed.
Example: The command is sent. The controller responds with the following:
This command transmits 61H followed by the active addresses for switch 1 and 2 in hex format.
This command sets the version of the data in the FLASH memory. Default value (00H).
This command uploads the version of the data in the FLASH memory to the host in one byte HEX
format.
command format: 2FH [LCD Module #] [LED code]
transmit format:
command format:
transmit format:
command format:
transmit format:
command format:
transmit format:
command format:
transmit format:
61H
61
Toll Free 1.877.2BUYNKK (877.228.9655) • Phone 480.991.0942 • Fax 480.998.1435
[mode]
31
(xxH)
(xxH) (xxH) (xxH)
(xxH) (xxH)
(xxH) (xxH)
(xxH) (xxH)
26H
26H
26H
26H
IS-Dev Kit-5 and IS-Dev Kit-6 Users
[Controller name]
www.nkkswitches.com • Email engineering@nkkswitches.com
43 30 32 30 33
52H
00H
42H
41H
(31H or 32H)
[Data Version]
58H
(xxAH)
Manual
[version]
(xxAH)
3131
79H
79
Page 12 of 24
1209