SD307EVK National Semiconductor, SD307EVK Datasheet
![BOARD EVAL CABLE DVR HD/SD SDI](/photos/39/50/395052/4649845_sml.jpg)
SD307EVK
Specifications of SD307EVK
Related parts for SD307EVK
SD307EVK Summary of contents
Page 1
... The SD303/SD307 Evaluation Kit (EVK) enables evaluation of the LMH0303 3G/HD/SD SDI Cable Driver with Cable Detect or the LMH0307 3G/HD/SD SDI Dual Cable Driver with Cable Detect. A graphical user interface allows managing the SMBus registers of the LMH0303 or LMH0307 device. Evaluation Kit (SD303EVK / SD307EVK) Contents The EVK contains the following parts: • ...
Page 2
... SD303/SD307 EVK User Guide Rev 1.2 Figure 1. SD303/SD307 Evaluation Board © 2010, National Semiconductor Corp. ...
Page 3
... RSTO ¯¯¯¯¯ (pins 17-18). This jumper block (or individual © 2010, National Semiconductor Corp. ¯¯¯¯¯ should be terminated with a 75Ω BNC ¯¯¯¯ detection still ...
Page 4
... The device will power back on once an input © 2010, National Semiconductor Corp. ¯¯¯¯ is used to reset the cable ¯¯¯¯ = 1), and Red when ¯ ...
Page 5
... LOS detected Table 3. SD303/SD307 Push Button Controls ¯¯¯¯ =0 and reset the device. Push again to set RSTI © 2010, National Semiconductor Corp. Function when OFF Board not powered N/A N/A No function, LED always off ...
Page 6
... Select “Search for the best driver in these locations”. Uncheck “Search removable media” and check “Include this location in the search”. 4. Browse to the Install Directory which is typically located at “C:\Program Files\National Semiconductor Corp\Analog LaunchPAD\vx.x.x\Drivers” and select the “Next” button. Windows should find the driver. ...
Page 7
... Startup Make sure all the software has been installed and the hardware is powered on and connected to the PC. Execute “Analog LaunchPAD” from the start menu. The default start menu location is “Programs\National Semiconductor Corp\Analog LaunchPAD vx.x.x\Analog LaunchPAD”. The application should come up in the state shown below (for the LMH0307 does not, see “Trouble Shooting” ...
Page 8
... LMH0303 and LMH0307 Tab The LMH0303/LMH0307 tabs present a high level view of the cable driver. Figure 4 shows this tab for the LMH0307, and Figure 5 shows this tab for the LMH0303. SD303/SD307 EVK User Guide Rev 1.2 Figure 3. LMH0307 Information Tab © 2010, National Semiconductor Corp. ...
Page 9
... SD303/SD307 EVK User Guide Rev 1.2 Figure 4. LMH0307 Main Tab Figure 5. LMH0303 Main Tab © 2010, National Semiconductor Corp. ...
Page 10
... Enable checkbox will force the LMH0303/LMH0307 into a deep power down mode. RSTI The RSTI checkbox controls the RSTI the cable driver in reset. SD303/SD307 EVK User Guide Rev 1.2 ¯¯¯¯ pin. This checkbox is checked for normal operation, and un-checked to put © 2010, National Semiconductor Corp. ...
Page 11
... P-P ¯¯¯¯¯¯ pin. The FAULT LED is Green to indicate no faults are © 2010, National Semiconductor Corp. ¯¯¯¯¯¯ = 0). The Auto Refresh ¯¯¯¯¯¯ pin. ¯¯¯¯¯¯ is ...
Page 12
... Value field. After setting the appropriate register value, the Apply button must be pressed to apply the changes. The detailed view of the STATUS register is shown in Figure 7 with Verbose Descriptions checked and Figure 8 with Verbose Descriptions un-checked. SD303/SD307 EVK User Guide Rev 1.2 Figure 6. LMH0307 Registers Tab © 2010, National Semiconductor Corp. ...
Page 13
... Figure 7. LMH0307 Registers Tab with Verbose Descriptions Figure 8. LMH0307 Registers Tab without Verbose Descriptions The Display button provides another view of the register set and is depicted in Figure 9. The Display dialog supports the Windows copy command (Ctrl+c). SD303/SD307 EVK User Guide Rev 1 © 2010, National Semiconductor Corp. ...
Page 14
... DSA 71254 12.5 GHz Oscilloscope. SDO0 Test Results Figure 8 shows the typical SDO0 output waveform from the LMH0307. SD303/SD307 EVK User Guide Rev 1.2 Figure 9. LMH0307 Register Display ¯¯¯¯¯ is terminated with a 75Ω BNC terminator © 2010, National Semiconductor Corp. ...
Page 15
... Figure 10. LMH0307 SDO0 Output Waveform at 2.97 Gbps SD303/SD307 EVK User Guide Rev 1 © 2010, National Semiconductor Corp. ...
Page 16
... It may also be that the USB driver is not installed. Check the device manager. There should be an ”NSC ALP Nano Atmel” device under the “Universal Serial Bus Controllers” as shown below in Figure 12. Figure 12. Windows XP, Analog LauchPAD USB Driver SD303/SD307 EVK User Guide Rev 1 © 2010, National Semiconductor Corp. ...
Page 17
... After demo mode is disabled, the ALP software will poll the ALP hardware. The ALP software will update and have only “LMH0303” or “LMH0307” under the “Devices” pull down menu. SD303/SD307 EVK User Guide Rev 1.2 Figure 13. Analog LaunchPAD in Demo Mode © 2010, National Semiconductor Corp. ...
Page 18
... Figure 15. Analog LaunchPAD Screen with Demo Mode Off SD303/SD307 EVK User Guide Rev 1 © 2010, National Semiconductor Corp. ...
Page 19
... Regulator, LDO, 300mA, 3.3V, 8MSOP U3 1 LMH0307 3G SDI Dual Cable Driver, LLP16 X1 1 Crystal, 8.00 MHz , 8 pF, Fund, SMD SD303/SD307 EVK User Guide Rev 1 © 2010, National Semiconductor Corp. Manufacturer Manufacturer Part No. Panasonic ECJ-0EB1A105M Panasonic ECJ-1VB0J475M Panasonic ECJ-1VC1H101J Panasonic ECJ-1VB1H104K Panasonic ...
Page 20
... Appendix Additional typical performance plots measured with the SD303EVK and SD307EVK are provided as reference. ORL (Output Return Loss) plots are shown for each output. Eye patterns showing transition times and jitter are shown for 2.97 Gbps. Amplitude measurements are shown for the outputs at 270 Mbps. ...
Page 21
... SD303/SD307 EVK User Guide Rev 1.2 ORL Plot - Channel 0 – Positive ORL Plot - Channel 1 – Positive © 2010, National Semiconductor Corp. ...
Page 22
... SD303/SD307 EVK User Guide Rev 1.2 ORL Plot - Channel 1 – Negative Smith Chart – Channel 0 – Positive © 2010, National Semiconductor Corp. ...
Page 23
... EYE - Channel 0 – Positive – Transition Times 2.97Gbps EYE - Channel 0 – Positive – Jitter SD303/SD307 EVK User Guide Rev 1 © 2010, National Semiconductor Corp. ...
Page 24
... Mbps EYE – Channel 0 – Negative – Color Bar - Amplitude 270 Mbps EYE – Channel 0 – Positive – Color Bar – Amplitude SD303/SD307 EVK User Guide Rev 1 © 2010, National Semiconductor Corp. ...
Page 25
... Mbps EYE – Channel 1 – Negative – Color Bar – Amplitude 270 Mbps EYE – Channel 1 – Positive – Color Bar – Amplitude Schematic SD303/SD307 EVK User Guide Rev 1 © 2010, National Semiconductor Corp. ...
Page 26
DAP RSTIbar RSTIbar RSTObar ENABLE ENABLE SDO1bar SDA SDO1 SCL FAULT SD/HDbar ...
Page 27
PB7 18 INT4_PE4 19 INT5_PE5 20 RESETz 21 VCC 22 GND 23 XTAL2 24 XTAL1 25 SCL SCL_PD0 26 SDA SDA_PD1 27 INT2_PD2 28 INT3_PD3 29 PD4 30 PD5 31 PD6 32 PD7 ...