MAX15501EVKIT+ Maxim Integrated Products, MAX15501EVKIT+ Datasheet - Page 7

• Manufacturer Part Number: MAX15501EVKIT+
• Description: KIT EVAL FOR MAX15501
• Manufacturer: Maxim Integrated Products

Specifications of MAX15501EVKIT+

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The MAX15501 EV kit provides a terminal block (J3)
that can be used to connect to the external load. By
default, the OUT signal of the MAX15501 connects to
the OUTPUT pin (pin 1) of the terminal block through an
on-board 41.2I sensing resistor (RS4).
The load should be connected between the OUTPUT
(pin 1) and AGND (pin 2) pins of the terminal block. Pins
Table 3. Jumper Settings
JUMPER
JU10
JU12
JU13
JU14
JU15
JU16
JU1
JU2
JU3
JU4
JU5
JU6
JU7
JU8
JU9
POSITION
_______________________________________________________________________________________
SHUNT
1-2*
1-2*
1-2*
1-3*
1-3*
1-2*
1-2*
1-2*
1-2*
1-2*
1-2*
1-2*
1-2*
1-2*
1-2*
2-3
2-3
2-3
1-2
1-4
1-2
1-4
2-3
2-3
2-3
2-3
2-3
2-3
2-3
2-3
2-3
2-3
MAX15501’s ERROR signal connected to on-board microcontroller
MAX15501’s ERROR signal connected to the J2 connector (pin J2-11)
MAX15501’s READY signal connected to on-board microcontroller
MAX15501’s READY signal connected to the J2 connector (pin J2-9)
MAX15501’s OUTDIS signal connected to on-board microcontroller
Connect external OUTDIS signal to the on-board OUTDIS pad
MAX15501’s FSSEL connected to ground
MAX15501’s FSSEL signal connected to on-board microcontroller
MAX15501’s FSSEL connected to DVDD
MAX15501’s FSMODE connected to ground
MAX15501’s FSMODE signal connected to on-board microcontroller
MAX15501’s FSMODE connected to DVDD
MAX15501’s CS1 signal connected to on-board microcontroller
Connect external CS1 signal to pin J2-1 of the J2 connector
SCLK signal connected to on-board microcontroller
Connect external SCLK signal to pin J2-3 of the J2 connector
MAX15501’s DIN signal connected to on-board microcontroller
Connect external MOSI signal to pin J2-5 of the J2 connector
MAX15501’s DOUT signal connected to on-board microcontroller
Connect external MISO signal to pin J2-7 of the J2 connector
MAX15501’s CS2 signal connected to on-board DAC’s READY signal
Connect external CS2 signal to pin J2-13 of the J2 connector
MAX15501’s DVDD connected to on-board digital supply
Connects the external DVDD to the DVDD pad
MAX15501’s AIN signal connected to on-board DAC output
Connect external AIN signal to the on-board AIN pad
The OUT signal of the MAX15501 connects to the OUTPUT pin of the J3 connector through a
5.1I resistor when the shunt is installed on jumper JU22
MAX15501’s output connected to the on-board OUT pad
MAX5138’s LDAC signal connected to on-board microcontroller
Connect external LDAC signal to pin J2-15 of the J2 connector
MAX5138’s CS signal connected to on-board microcontroller
Connect external CS signal to pin J2-17 of the J2 connector
Terminal Block
MAX15501 Evaluation Kit
3 and 4 of the terminal block are the Kelvin sense voltage
inputs (SENSEVP and SENSEVN) of the MAX15501. The
load should also be connected between pins 3 and 4 of
the terminal block.
To construct the Typical Operating Circuit from the
MAX15501 IC data sheet, place shunts in their default
positions, as shown in Table 3.
DESCRIPTION
Jumpers
7