LM8300-REF-01 National Semiconductor, LM8300-REF-01 Datasheet
LM8300-REF-01
Specifications of LM8300-REF-01
Related parts for LM8300-REF-01
LM8300-REF-01 Summary of contents
Page 1
... Four Wire Resistive Touchscreen Controller with Brownout 1.0 General Description The LM8300/8500 is a 4-wire resistive touch screen control- ler. The controller samples and drives the touch screen without the need of any external hardware. The built in 10-bit A/D provides a maximum of 500 coordinate pairs per second (cpps) ...
Page 2
... Block Diagram * This pin is available in the LM8500 unused in the LM8300. 4.0 Ordering Information LM Family and Feature Set Indicator 8300 = Low Brownout Voltage 8500 = High Brownout Voltage www.national.com Part Numbering Scheme 8300 H No. Of Pins Pin LQ = LLP Pin MT = TSSOP VA = PLCC 2 20037201 VA 9 Package Type Temperature +70˚ ...
Page 3
General Description ..................................................................................................................................... 1 2.0 Features ....................................................................................................................................................... 1 3.0 Block Diagram .............................................................................................................................................. 2 4.0 Ordering Information .................................................................................................................................... 2 5.0 Connection Diagrams ................................................................................................................................... 4 6.0 Pin Descriptions ........................................................................................................................................... 5 7.0 Absolute Maximum Ratings ......................................................................................................................... 7 8.0 Electrical Characteristics .............................................................................................................................. 7 ...
Page 4
... Plastic Chip Package See NS Package Number V44A * This pin is available in the LM8500 unused in the LM8300. Top View LLP Package See NS Package Number LQA44A www.national.com 20037202 * This pin is available in the LM8500 unused in the LM8300. Top View TSSOP Package See NS Package Number MTD48 20037203 4 20037204 ...
Page 5
Pin Descriptions Pin Name Direction RESET I DTR I WD_OUT O 1 CLK_SET I 2 Unused 2 Unused 2 Unused 2 Unused OSC_OUT O OSC_IN I 2 Unused 2 Unused UART_TX O UART_RX I SHUTDOWN I 2 Unused 2 ...
Page 6
Pin Descriptions Pin Name Direction LED Output 2 Unused 2 Unused 2 Unused Note 1: This is available in the LM8500 only. Note 2: These pins are for future functional expansions. www.national.com (Continued) Pinouts for 44- and 48-Pin Packages ...
Page 7
... Absolute Maximum Ratings 3) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage ( Voltage at Any Pin Total Current into V Pin (Source) CC 8.0 Electrical Characteristics DC Electrical Characteristics (0˚C ≤ T Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. ...
Page 8
... GENERAL The LM8300/8500 is a 4-wire resistive touch screen control- ler. The primary communication is through the built in UART operating at a baud rate of 38400. The LM8300/8500 has the ability to measure pressure on the Z-axis, in addition to the X-Y coordinates. The device has the capability and 13 point calibration ...
Page 9
Functional Description LED — Optional LED output. When the controller is oper- ating in normal (non power save) mode, a low is output to the pin. When the controller is in power save mode, a high is output to ...
Page 10
Functional Description Byte Command Byte 2 1 Read stored $B4 calibration points Set focus $B8 $0-$3F value (# of pixels on touch panel) Set # of $BA $01, $02, samples per $04, $08, coordinate (1, $10, ...
Page 11
Functional Description Byte #11: Number of calibration coordinates ( 13) Byte #12: Toggle-flags: Bit #5: calibration coordinates check (0=disabled, 1=enabled) Bit #4: Pressure measurement 1=enabled) Bit #3: Echo mode (0=disabled, 1=enabled) Bit #2: Self Power-Down mode ...
Page 12
Functional Description lines. This option can be used in high noise environments to significantly improve performance and accuracy of the touch screen controller. The default setting is filter path enabled. $A2: Toggle disable/enable self-power down Reply Byte #1: $CA ...
Page 13
... UART, the wake up command byte must be sent, followed by a minimum time delay of 1ms for the LM8500 and 3ms for the LM8300 before sending any command byte. The delay time is needed to allow the oscil- lator to restart and stabilize. Table 2. Startup Times shows the average startup time for a given operating frequency ...
Page 14
... The RESET input initializes the device when pulled low. The RESET pin must be held low for a minimum of 0.5µs for the LM8500 and a minimum of 1.5µs for the LM8300 to guaran- tee a valid reset. Reset should also be wide enough to ensure crystal start-up upon power-up. The R/C circuit shown in Figure optional circuitry that will provide a delay 5 times (5x) greater than the power supply ...
Page 15
... FIGURE 4. Brownout Reset Operation counts down a value between 120-128µs for the LM8500 and 360-384µs id for the LM8300. At this time, the internal reset will be gener- ated. The device has a built in watchdog monitoring module to prevent runaway code. To use the watchdog feature, the remains above WD_OUT pin must be connected to the RESET pin ...
Page 16
Calibration (Continued) in Table 3. Two Points Calibration, Table 4. Five Points Calibration, and Table 5. Thirteen Points Calibration respec- tively. FIGURE 5. Two Points Calibration Mapping FIGURE 6. Five Points Calibration Mapping FIGURE 7. Thirteen Points Calibration Mapping ...
Page 17
Calibration (Continued) FIGURE 8. Calibration Procedures with Coordinates Checking Enabled 14.2 CALIBRATION PROCEDURES WITH COORDINATES CHECKING ENABLED calibration with coordinates checking enabled, first ensure the Calibration Coordinates Checking is enabled on the device. This can be ...
Page 18
Calibration (Continued) send a reply byte of $CC to the TS driver. At this point, the TS driver should either notify the user to redo the calibration point or automatically redo the calibration again. If the self- test was ...
Page 19
... Physical Dimensions inches (millimeters) unless otherwise noted LLP Package (LQA) Order Number LM8300HLQ9 or LM8500HLQ9 NS Package Number LQA44A TSSOP Package (MTD) Order Number LM8300IMT9 or LM85009IMT9 NS Package Number MTD48 19 www.national.com ...
Page 20
... National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. inches (millimeters) unless otherwise noted (Continued) Plastic Leaded Chip Carrier (VA) Order Number LM8300HVA9 or LM8500HVA9 NS Package Number V44A 2. A critical component is any component of a life ...