MAX1231EVC16 Maxim Integrated Products, MAX1231EVC16 Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX1231EVC16
Manufacturer Part Number
MAX1231EVC16
Description
EVAL KIT FOR MAX1231
Manufacturer
Maxim Integrated Products
Specifications of MAX1231EVC16
Number Of Adc's
1
Number Of Bits
12
Sampling Rate (per Second)
300k
Data Interface
Serial
Inputs Per Adc
16 Single Ended or 8 Differential
Input Range
±VREF/2
Power (typ) @ Conditions
1.86mW @ 300kSPS
Voltage Supply Source
Single Supply
Operating Temperature
0°C ~ 70°C
Utilized Ic / Part
MAX1231
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
12-Bit 300ksps ADCs with FIFO,
Temp Sensor, Internal Reference
The MAX1227/MAX1229/MAX1231 communicate
between the internal registers and the external circuitry
through the SPI-/QSPI-compatible serial interface.
Table 1 details the registers and the bit names. Tables
2–7 show the various functions within the conversion
register, setup register, averaging register, reset regis-
ter, unipolar register, and bipolar register.
The conversion time for each scan is based on a num-
ber of different factors: conversion time per sample,
samples per result, results per scan, if a temperature
measurement is requested, and if the external refer-
ence is in use.
Use the following formula to calculate the total conver-
sion time for an internally timed conversion in clock
modes 00 and 10 (see the Electrical Characteristics
section as applicable):
where:
t
n
n
by number of channels being scanned or by NSCAN1,
NSCAN0
t
to zero if temp measurement is not requested
t
reference is already powered up or external reference
is being used
12
Table 1. Input Data Byte (MSB First)
*Unipolar/bipolar channels 8–15 are only valid on the MAX1229 and MAX1231.
*Unipolar/bipolar channels 12–15 are only valid on the MAX1231.
X = Don’t care.
cnv
TS
RP
Conversion
Setup
Averaging
Reset
Unipolar mode (setup)
Bipolar mode (setup)
total conversion time = t
avg
result
REGISTER NAME
= time required for temperature measurement; set
= internal reference wake up; set to zero if internal
= t
______________________________________________________________________________________
= samples per result (amount of averaging)
= number of FIFO results requested; determined
acq
(max) + t
Applications Information
conv
Conversion Time Calculations
(max)
cnv
UCH0/1
BCH0/1
BIT 7
Register Descriptions
1
0
0
0
x n
avg
x n
CHSEL3
UCH2/3
BCH1/2
BIT 6
result
1
0
0
+ t
TS
CHSEL2
CKSEL1
UCH4/5
BCH4/5
+ t
BIT 5
1
0
RP
CHSEL1
CKSEL0
AVGON
UCH6/7
BCH6/7
In clock mode 01, the total conversion time depends on
how long CNVST is held low or high, including any time
required to turn on the internal reference. Conversion
time in externally clocked mode (CKSEL1, CKSEL0 = 11)
depends on the SCLK period and how long CS is held
high between each set of eight SCLK cycles. In clock
mode 01, the total conversion time does not include the
time required to turn on the internal reference.
Select active analog input channels, scan modes, and
a single temperature measurement per scan by writing
to the conversion register. Table 2 details channel
selection, the four scan modes, and how to request a
temperature measurement. Request a scan by writing
to the conversion register when in clock mode 10 or 11,
or by applying a low pulse to the CNVST pin when in
clock mode 00 or 01.
A conversion is not performed if it is requested on a
channel that has been configured as CNVST or REF-.
Do not request conversions on channels 8–15 on the
MAX1227 and channels 12–15 on the MAX1229. Set
CHSEL3:CHSELO to the lower channel’s binary value. If
the last two channels are configured as a differential
pair and one of them has been reconfigured as CNVST
or REF-, the pair is ignored.
Select scan mode 00 or 01 to return one result per sin-
gle-ended channel and one result per differential pair
within the requested range, plus one temperature result if
selected. Select scan mode 10 to scan a single input
channel numerous times, depending on NSCAN1 and
NSCAN0 in the averaging register (Table 6). Select scan
mode 11 to return only one result from a single channel.
Write a byte to the setup register to configure the clock,
reference, and power-down modes. Table 3 details the
BIT 4
1
REFSEL1
UCH8/9*
BCH8/9*
CHSEL0
NAVG1
RESET
BIT 3
UCH10/11 UCH12/138** UCH14/15**
BCH10/11
REFSEL0
SCAN1
NAVG0
BIT 2
X
BCH12/13** BCH14/15**
DIFFSEL1
Conversion Register
NSCAN1
SCAN0
BIT 1
X
Setup Register
DIFFSEL0
NSCAN0
TEMP
BIT 0
X