LM3481EVAL National Semiconductor, LM3481EVAL Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
LM3481EVAL
Manufacturer Part Number
LM3481EVAL
Description
BOARD EVAL FOR LM3481
Manufacturer
National Semiconductor
Specifications of LM3481EVAL
Main Purpose
DC/DC, Step Up
Outputs And Type
1, Non-Isolated
Voltage - Output
12V
Current - Output
1.5A
Voltage - Input
3 ~ 11V
Regulator Topology
Boost
Frequency - Switching
300kHz
Board Type
Fully Populated
Utilized Ic / Part
LM3481
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Power - Output
-
www.national.com
Designing SEPIC Using LM3481
Since the LM3481 controls a low-side N-Channel MOSFET,
it can also be used in SEPIC (Single Ended Primary Induc-
tance Converter) applications. An example of SEPIC using
the LM3481 is shown in
output voltage can be higher or lower than the input voltage.
The SEPIC uses two inductors to step-up or step-down the
input voltage. The inductors L1 and L2 can be two discrete
inductors or two windings of a coupled transformer since
equal voltages are applied across the inductor throughout the
switching cycle. Using two discrete inductors allows use of
catalog magnetics, as opposed to a custom transformer. The
input ripple can be reduced along with size by using the cou-
pled windings of transformer for L1 and L2.
Due to the presence of the inductor L1 at the input, the SEPIC
inherits all the benefits of a boost converter. One main ad-
vantage of SEPIC over a boost converter is the inherent input
to output isolation. The capacitor C
the output and provides protection against shorted or mal-
functioning load. Hence, the SEPIC is useful for replacing
boost circuits when true shutdown is required. This means
that the output voltage falls to 0V when the switch is turned
off. In a boost converter, the output can only fall to the input
voltage minus a diode drop.
The duty cycle of a SEPIC is given by:
In the above equation, V
FET, Q1, and V
POWER MOSFET SELECTION
As in a boost converter, the parameters governing the selec-
tion of the MOSFET are the minimum threshold voltage, V
DIODE
is the forward voltage drop of the diode.
Figure
Q
is the on-state voltage of the MOS-
17. As shown in
S
isolates the input from
FIGURE 17. Typical SEPIC Converter
Figure
17, the
TH
18
(MIN)
reverse transfer capacitance, C
to source voltage, V
SEPIC is given by:
The selected MOSFET should satisfy the condition:
The peak switch current is given by:
Where ΔI
rents of inductors L1 and L2 respectively.
The rms current through the switch is given by:
POWER DIODE SELECTION
The Power diode must be selected to handle the peak current
and the peak reverse voltage. In a SEPIC, the diode peak
current is the same as the switch peak current. The off-state
voltage or peak reverse voltage of the diode is V
Similar to the boost converter, the average diode current is
equal to the output current. Schottky diodes are recommend-
ed.
, the on-resistance, R
L1
and ΔI
V
SW(PEAK)
L2
V
are the peak-to-peak inductor ripple cur-
DS(MAX)
DS(MAX)
= V
DS(ON)
IN
. The peak switch voltage in a
> V
+ V
, the total gate charge, Q
RSS
SW(PEAK)
OUT
, and the maximum drain
+ V
DIODE
IN
+ V
g
, the
OUT
20136544
.