MAX5258EVKIT+ Maxim Integrated Products, MAX5258EVKIT+ Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX5258EVKIT+
Manufacturer Part Number
MAX5258EVKIT+
Description
KIT EVAL FOR MAX5258
Manufacturer
Maxim Integrated Products
Specifications of MAX5258EVKIT+
Number Of Dac's
8
Number Of Bits
8
Outputs And Type
8, Single Ended
Data Interface
Serial
Settling Time
10µs
Dac Type
Voltage
Voltage Supply Source
Single
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
MAX5258
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
LDAC is typically used in 4-wire interfaces (Figure 4).
This command is level sensitive, and it allows asyn-
chronous hardware control of the DAC outputs. With
LDAC low, all eight DAC registers are transparent, and
any time an input register is updated, the DAC output
immediately follows.
DOUT is the internal shift-register’s output. DOUT can
be programmed to clock out data on the falling edge of
SCLK (mode 0) or the rising edge (mode 1). In mode 0,
output data lags input data by 16.5 clock cycles, main-
taining compatibility with MICROWIRE and SPI. In
mode 1, output data lags input data by 16 clock cycles.
On power-up, DOUT defaults to mode 0 timing. DOUT
never three-states; it always actively drives either high
or low and remains unchanged when CS is high.
The MAX5258/MAX5259 are MICROWIRE (Figure 5)
and SPI/QSPI (Figure 6) compatible. For SPI and QSPI,
clear the CPOL and CPHA configuration bits (CPOL =
CPHA = 0). The SPI/QSPI CPOL = CPHA = 1 configura-
tion can also be used if the DOUT output is ignored.
The MAX5258/MAX5259 can interface with Intel’s
80C5X/80C3X family in mode 0 if the SCLK clock polar-
ity is inverted. Universally, if a serial port is not avail-
able, three lines from one of the parallel ports can be
used for bit manipulation.
Digital feedthrough at the voltage outputs is greatly
minimized by operating the serial clock only to update
the registers. See the Clock Feedthrough photo in the
Typical Operating Characteristics section. The clock
idle state is low.
Any number of MAX5258/MAX5259s can be daisy-
chained by connecting DOUT of one device to DIN of
the following device in the chain with all devices in
mode zero. The NOP instruction (Table 1) allows data
to be passed from DIN to DOUT without changing the
input or DAC registers of the passing device. A 3-wire
interface updates daisy-chained or individual
MAX5258/MAX5259s simultaneously by bringing CS
high (Figure 7).
The MAX5258/MAX5259 use a matrix decoding archi-
tecture for the DACs, which saves power in the overall
system. The external reference voltage is divided down
by a resistor string placed in a matrix fashion. Row and
______________________________________________________________________________________
Interfacing to the Microprocessor
LDAC Operation (Hardware)
+3V/+5V, Low-Power, 8-Bit Octal DAC
Daisy-Chaining Devices
Serial Data Output
Analog Section
DAC Operation
with Rail-to-Rail Output Buffers
column decoders select the appropriate tab from the
resistor string to provide the needed analog voltages.
The resistor string presents a code-independent input
impedance to the reference and guarantees a monoto-
nic output. Figure 8 shows a simplified diagram of one
of the eight DACs.
The voltage at REF sets the full-scale output voltage for
all eight DACs. The 230kΩ typical input impedance at
REF is code independent. The output voltage for any
DAC can be represented by a digitally programmable
voltage source as follows:
where NB is the numerical value of the DAC’s binary
input code.
All MAX5258/MAX5259 voltage outputs are internally
buffered by precision unity-gain followers that slew at
about 0.55V/µs. The outputs can swing from GND to
V
the amplifier outputs will typically settle to 1/2LSB in
10µs when loaded with 10kΩ in parallel with 100pF.
The buffer amplifiers are stable with any combination of
resistive (≥10kΩ) or capacitive (≤100pF) loads.
The output buffer can have a negative input offset volt-
age that would normally drive the output negative, but
since there is no negative supply, the output remains at
GND (Figure 9). When linearity is determined using the
endpoint method, it is measured between code 10 (0A
hex) and full-scale code (FF hex) after offset and gain
error are calibrated out. With a single-supply, negative
offset causes the output not to change with an input
code transition near zero (Figure 9). Thus, the lowest
code that produces a positive output is the lower end-
point.
Figure 3. Serial Input Format
DD
. With a 0 to V
DOUT
THIS IS THE FIRST BIT SHIFTED IN
DAC Linearity and Voltage Offset
X X A2 A1 A0 C2 C1 C0 D7 D6 . . . D1 D0
V
Applications Information
OUT
CONTROL AND
ADDRESS BITS
REF
= (NB
(or V
✕
REF
V
Output Buffer Amplifiers
MSB
REF
8-BIT DAC DATA
to 0) output transition,
) / 256,
Reference Input
LSB
DIN
15