LM3410XMFLEDEV National Semiconductor, LM3410XMFLEDEV Datasheet

no-image

LM3410XMFLEDEV

Manufacturer Part Number
LM3410XMFLEDEV
Description
BOARD EVAL LM3410 BOOST SOT23
Manufacturer
National Semiconductor
Series
PowerWise®r
Datasheets

Specifications of LM3410XMFLEDEV

Outputs And Type
1, Non-Isolated
Voltage - Output
3 ~ 24V
Features
Thermal Shutdown Protection
Voltage - Input
2.7 ~ 5.5V
Utilized Ic / Part
LM3410
Kit Contents
Board, Datasheet
Svhc
No SVHC (15-Dec-2010)
Kit Features
Converts 2.7V To 5.5V Input And Illuminates Five 50 MA LEDs In Series Using The LM3410X
Mcu Supported Families
LM3410
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Current - Output / Channel
-
© 2008 National Semiconductor Corporation
LM3410X LED Driver 5-Pin
SOT-23 Demo Board
Introduction
The demo board included in this shipment converts 2.7V to
5.5V input, and illuminates four 50mA LED’s in series using
the LM3410X 1.6MHz LED driver switching converter. This is
a 2-layer board using the bottom layer as a Ground plane.
A bill of materials below describes the parts used on this demo
board. A schematic and layout have also been included below
Pin Descriptions - 5-Pin SOT23
Pin
1
2
3
4
5
Name
GND
DIM
SW
VIN
FB
Function
Output switch. Connect to the inductor, output diode.
Signal and power ground pin. Place the bottom resistor of the feedback network as close as possible to
this pin.
Feedback pin. Connect FB to external resistor divider to set output voltage.
Dimming & shutdown control input. Logic high enables operation. Duty Cycle from 0 to 100%. Do not
allow this pin to float or be greater than VIN + 0.3V.
Supply voltage pin for power stage, and input supply voltage.
300487
LM3410X 5-Pin SOT23 Schematic
Pinout
National Semiconductor
Application Note 1773
Matthew Reynolds
January 31, 2008
along with measured performance characteristics. The above
restrictions for the input voltage are valid only for the demo
board as shipped with the demo board schematic below.
Operatiing Conditions
V
V
I
O
IN
O
= 50mA
= 2.7V to 5.5V
V
30048702
F
x 4 + V
FB
3.6V x 4 + 0.198V
14.4V
www.national.com
30048701

Related parts for LM3410XMFLEDEV

LM3410XMFLEDEV Summary of contents

Page 1

... DIM allow this pin to float or be greater than VIN + 0.3V. 5 VIN Supply voltage pin for power stage, and input supply voltage. © 2008 National Semiconductor Corporation National Semiconductor Application Note 1773 Matthew Reynolds January 31, 2008 along with measured performance characteristics. The above restrictions for the input voltage are valid only for the demo board as shipped with the demo board schematic below ...

Page 2

Bill of Materials LM3410X Part ID U1 C1, Input Cap C2 Output Cap D1, Catch Diode 0. LED’s SMD-1206, 50mA, V LM3410X Efficiency vs Input Voltage Series LEDs @ 50mA LM3410X Average LED Current vs Duty-Cycle & ...

Page 3

PCB Layout Demonstration Board Top Layer Demonstration Board Bottom Layer 3 30048705 30048706 www.national.com ...

Page 4

V > 5.5V Application Circuit PWR The circuit shown in Figure 1 allows for a single supply to be used with a simple zenner diode regulation circuit to provide the LM3410 with a housekeeping and driver voltage that ...

Page 5

Part ID Part Value U1 2. Input Cap 10µF, 6.3V, X5R PWR C2 Output Cap 1µF, 25V, X5R C3 V Input Cap 0.1µF, 6.3V, X5R IN D1, Catch Diode 0.43V , Schotky, 0.5A, 30V f L1 ...

Page 6

... For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Amplifiers www.national.com/amplifiers Audio www.national.com/audio Clock Conditioners www.national.com/timing Data Converters www.national.com/adc Displays www.national.com/displays Ethernet www.national.com/ethernet Interface www.national.com/interface LVDS www.national.com/lvds Power Management www.national.com/power Switching Regulators www.national.com/switchers LDOs www ...

Related keywords