STEVAL-MKI030V1 STMicroelectronics, STEVAL-MKI030V1 Datasheet - Page 103

• Manufacturer Part Number: STEVAL-MKI030V1
• Description: BOARD DEMO STM8S207R6/LIS331DLH
• Manufacturer: STMicroelectronics
• Series: MEMSr

Specifications of STEVAL-MKI030V1

• Design Resources: STEVAL-MKI030V1 Schematic
• Sensor Type: Accelerometer, 3 Axis
• Sensing Range: ±2g, 4g, 8g
• Interface: I²C, SCI
• Sensitivity: 3.9mg/digit, 2mg/digit, 1mg/digit
• Voltage - Supply: 4.5V
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: LIS331DLH, STM8S207R6T6
• Sensing Axis: Triple Axis
• Operating Voltage: 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-8852

STM8S207xx, STM8S208xx
Table 58.
13-Apr-2010
10-Jul-2009
Date
Document revision history (continued)
Revision
cont’d
8
9
Section 10: Electrical
updated
operating
Section 10.3.1: VCAP external
replaced
updated
application with I2C bus and timing
Removed
Added link between ordering information
features
Document status changed from “preliminary data” to “datasheet”.
Table 2: STM8S20xxx performance line
STM8S207C8 is 16 (not 13).
Table 3: Peripheral clock gating bit assignments in CLK_PCKENR1/2
registers: updated bit positions for TIM2 and TIM3.
Figure 5: LQFP 48-pin
35 and 36; noted that these pins are available only in STM8S208xx
devices.
Figure 7: LQFP 32-pin
Table 6: Pin
availability and UART1_RX and UART3_RX pins.
Table 13: Option byte
bootloader option bytes to the option byte description table.
Added
Section 10.3: Operating
Table 18: General operating
and added data for ESR and ESL; removed “low power dissipation”
condition for T
Table 26: Total current consumption in halt mode at VDD = 5 V, TA -
40 to 85°
µA for the condition “Flash in powerdown mode, HSI clock after
wakeup”.
Table 33: HSI oscillator
calibrated values.
Functional EMS (electromagnetic susceptibility)
replaced “IEC 1000” with “IEC 61000”.
Electromagnetic interference (EMI)
J1752/3” with “IEC 61967-2”.
Table 57: Thermal
junction-ambient value of LQFP32 (7x7 mm) from 59 °C/W to 60
°C/W.
Doc ID 14733 Rev 11
Section 9: Unique ID
Table 15: Voltage characteristics
Figure 22
Table
Figure
C: replaced max value of I
conditions; updated VCAP specifications in
Table 56: Junction temperature range.
description: added footnotes concerning beCAN
A
2.
.
19; updated
characteristics: changed the thermal resistance
and
characteristics: Added data for TBD values;
description: added description of STM8L
pinout: added CAN_TX and CAN_RX to pins
pinout: replaced uart2 with uart3.
Figure
characteristics: updated the ACC
conditions: added introductory text.
conditions: replaced “C
(and listed this attribute in Features).
Table 35: RAM and hardware
Changes
35; added
capacitor; updated
diagram.
and
DD(H)
Table
features: high sink I/O for
Figure 40: Typical
Figure 49
at 85 °C from 30 µA to 35
and
48: replaced “SAE
Table 18: General
and
Revision history
Figure
EXT
and STM8S20xx
Table
Table 18
” with “VCAP”
HSI
18;
registers;
47:
factory
103/105
and in