ATEVKLCD101 Atmel, ATEVKLCD101 Datasheet
![KIT EVAL AVR32 VGA AUDIO](/photos/28/41/284165/atevklcd101_sml.jpg)
ATEVKLCD101
Specifications of ATEVKLCD101
Related parts for ATEVKLCD101
ATEVKLCD101 Summary of contents
Page 1
AVR32901: EVKLCD100/EVKLCD101 Hardware User's Guide Features • QVGA (EVKLCD100) or VGA (EVKLCD101) 5.7” LCD panel • AC97 codec with touch controller • Mono microphone input • Resistive touch panel • Stereo audio output 1 Introduction This application note describes how ...
Page 2
Hardware overview 2.1 EVKLCD100 and EVKLCD101 evaluation kits 2.1.1 AC97 codec specifications 2.1.2 LCD panel specifications AVR32901 2 The EVKLCD100 and EVKLCD101 evaluation kits, hereby known as EVKLCD10X kits, consist of a LCD mounted to a PCB. The headers ...
Page 3
Audio and touch panel connectors 2.1.4 TWI/SPI/UART extension connector 32124A-AVR32-05/09 On the right hand side of the EVKLCD10X kits there are a collection of two header connectors and two audio jacks. See Figure 2-2 and description in Table 2-1. ...
Page 4
NGW100 reference design AVR32901 4 The reference design NGW100 is used as a base for the EVKLCD10X kits. Although, other kits with similar expansion headers should also work fine with EVKLCD10X kits. See Figure 2-4 for a picture of ...
Page 5
Hardware assembly 3.1 Requirements 3.2 Soldering stack through headers on NGW100 32124A-AVR32-05/09 The following items are necessary to assemble an EVKLCD10X kit to the NGW100 board with similar expansion headers. • Three stack through headers (included in ...
Page 6
After inserting the stack through headers into NGW100 they must be soldered to the PCB. This is done by applying heat with the solder iron to the via and header pin and applying solder, see Figure 3-2. The solder should ...
Page 7
Connecting NGW100 board to EVKLCD100/EVKLCD101 32124A-AVR32-05/09 To connect the EVKLCD10X kit to the NGW100, align the expansion headers as shown in Figure 3-4. The EVKLCD10X kit is mounted on the back side of the NGW100. Apply an even force ...
Page 8
Powering up the NGW100 with EVKLCD100/EVKLCD101 AVR32901 8 When the EVKLCD10X kit is correctly assembled with the NGW100 the user can apply power to the NGW100 board to verify that the boards power up correctly. There is a green ...
Page 9
... NGW100 + EVKLCD101 evaluation kit. After configuring Buildroot for AVR32 the user should continue as described in the application note. Standalone users can get an introduction to using the LCD controller by reading application note AVR32114: Using the AVR32 LCD Controller available at http://www.atmel.com/dyn/products/app_notes.asp?family_id=682. software package can AVR32901 ...
Page 10
... FCC (except as may be otherwise noted on the board/kit). Atmel® supplied this board/kit “AS IS,” without any warranties, with all faults, at the buyer’s and further users’ sole risk ...
Page 11
... BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’ ...