28850 Parallax Inc, 28850 Datasheet - Page 3
![CARRIER BOARD BOARD OF EDU USB](/photos/9/25/92524/mfg_28850_sml.jpg)
28850
Manufacturer Part Number
28850
Description
CARRIER BOARD BOARD OF EDU USB
Manufacturer
Parallax Inc
Type
MCUr
Datasheet
1.28803.pdf
(5 pages)
Specifications of 28850
Contents
Board
Product
Microcontroller Accessories
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With/related Products
BASIC Stamp® 2 and Board of Education
For Use With
900-00014 - SERVO CONTROLLER PICO GWS28825 - MINI SOUND PLAYER SOUNDPAL130-28029 - KIT PARTS SMART SENSORS805-00006 - CABLE USB A TO MINI B27937 - MEMORY STICK DATALOGGER658-1021-5 - PROGRAMMER TEACLIPPER/STAMP30010 - BASIC STAMP LOGIC ANALYZER27220 - BOOK STAMPWORKS27330 - PROGRAMMER STACHE BASIC STAMP27218 - MANUAL BASIC STAMP VER 2.0
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Software and Hardware Installation:
1. Place the 4 rubber feet on the back of the board. in the spaces provided near each corner, but do not
2. Insert the BASIC Stamp module into the socket. Be sure to orient it properly, matching the small and
3. Connect Power to your Board. Place the 3-position switch to Off (position 0). Attach a 9V battery to
4. Install the BASIC Stamp Editor Software v2.2 or higher - it is available as a free download from
5. Install the Virtual Com Port Drivers.
Verifying your BASIC Stamp Programming Connection
In the BASIC Stamp Editor, from the toolbar menu
select Run → Identify. The Identification Window will
open, showing the status of the COM ports detected by
the BASIC Stamp Editor. Communication is confirmed
by a “Yes” in both the Loopback and Echo columns.
However, when using USB-based communication such
as with the BOE-USB, the Loopback column does not
always give reliable results, and a “YES” in the Echo
column
communication, and the Loopback status can be ignored.
CAUTION: Connecting and Disconnecting your USB Board Safely
Your PC is communicating with the BASIC Stamp through a virtual COM port that will open and close
each time you connect and disconnect your Board of Education USB.
operating system, take these precautions:
Copyright © Parallax, Inc. • BOE-USB (#28850) • v1.4 7/20/2007
cover the mounting holes. The feet will protect the back of the board from shorts and damage.
large chips on the module with the graphics on the board. Press down gently but firmly, being careful
not to bend any pins under the board.
the battery clip, or plug in a 6-9V 300 mA wall-mount supply. (If you will use your board with a 4-cell
AA battery pack, you must use 1.5V alkaline batteries - 1.2V rechargeable batteries supply a total of
4.8 V - not enough voltage for this 5 V device.) Move the switch to position 1(power to board only)
and verify that the power light comes on. Do not connect your board to your PC yet.
http://www.parallax.com/downloads.
Browse to http://www.parallax.com, and click on the USB Drivers
button on the home page. Follow the instructions on the Installing
USB Drivers page.1
Close the Debug Terminal before reprogramming, disconnecting, or reconnecting your board to
the USB port. If you forget to do this, you may receive and error message and/or freeze the BASIC
Stamp Editor when you next try to download a program. If this happens, close the BASIC Stamp
Editor with the Task Manager (Ctrl+Alt+Delete). If you do this repeatedly, you may need to reboot
your computer and/or reinstall the USB VCP drivers.
If your BASIC Stamp is actively transmitting data via its port (using the DEBUG or SEROUT 16
commands) and you disconnect and reconnect your board, the BASIC Stamp Editor may
misidentify it. To avoid this, turn off power to your board before reconnecting it to your PC.
Step 1: Download the Parallax USB Driver Installer
Step 2: Run the Installer, following the steps provided by the
Wizard prompts.
Step 3: Connect your Hardware.
is
usually
sufficient
confirmation
of
To avoid hanging up your
Page 3 of 5