PPM4-MK1(UN) Equinox Technologies, PPM4-MK1(UN) Datasheet - Page 5

• Manufacturer Part Number: PPM4-MK1(UN)
• Description: ISP PRODUCTION PROGRAMMER
• Manufacturer: Equinox Technologies
• Series: PPM4-MK1r
• Type: Production ISPr

Specifications of PPM4-MK1(UN)

• Contents: Programmer, Software, Cables and Documentation
• For Use With/related Products: ATMEL AT89S, AVR, AT91SAM7, NXP P89C51Rx2 P89C66x, Zensys, Serial EEPROM's
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 483-1021

Equinox Products Page - PPM4 MK1(UN) - Production ISP Programming Module - OVERVIEW
http://www.equinox-tech.com/products/details.asp?ID=1300
The 'Special Function Module contains the main 'I/O Driver Circuitry' which interfaces the
programmer electronics to the Target System. This module is interchangeable allowing a
Programming Interfaces Supported
JTAG ISP Programming support
Interchangeable I/O Driver Circuitry (SFM Modules)
Interchangeable 'I/O Connector Modules' support all popular ISP Header formats:
Atmel 10-way SPI Header (as per STK200 / STK500)
Atmel 6-way SPI Header
Equinox 10-way SPI header with support for Slave Select & SCK2
Atmel 10-way JTAG header (as per Atmel JTAG-ICE)
Equinox 10-way UART header for Atmel T89C51Rx2 (8051) and NXP (Philips) P89C51 ISP
FLASH microcontrollers
Fast Connect - clip-in wire connectors
Wire-wrap connectors
Atmel 3-wire SPI Interface + RESET - Atmel AVR and AT89S microcontrollers
Zensys - 3-wire SPI + RESET + PROG_ENABLE
JTAG - for Atmel AVR (supports JTAG chain programming)
JTAG - for AT91SAM7 (supports JTAG chain programming)
Atmel UART Bootloader - Atmel 89C51Rx2 (TXD, RXD, PSEN & RESET)
NXP (Philips) UART Bootloader - P89CRx2/66x (TXD, RXD, PSEN & RESET)
I2C Interface (SDA + SCL)
Supports high-speed JTAG programming of a single Atmel AVR microcontroller or
AT91SAM7 ARM microcontroller connected via the JTAG interface
Supports high-speed JTAG programming of multiple Atmel AVR or AT91SAM7
microcontrollers which are connected as part of a 'JTAG Chain' (JTAG daisy-chain mode).
Fast programming speeds via JTAG (3 - 4 times faster than SPI method)
Simple 4-wire JTAG Interface to microcontroller
Same JTAG Interface as Atmel JTAG ICE MK2 Debugger
User-selectable JTAG frequency
Supports JTAG Chain Validation
Supports checking of the 'JTAG ID' of both AVR and any generic JTAG devices eg. CPLD's
Supports automatic checking of 'Silicon Revision' of target JTAG device
The JTAG algorithms can be purchased as a License Upgrade to the standard PPM3-MK2
programmer (Order code: PPM4MK1-UPG7)
The JTAG I/O Connector Module IO-CON-3 is required to connect to an Atmel JTAG Target
System.
Test Equipment
Olimex - SAM7-P64
DEVELOPMENT BOARD
FOR AT91SAM7S64
ARM7TDMI-S MC
I/O Connector Module 11
- ATE RELAY Interface
>>
Page 5 of 7
2/17/2009
>>